🎃

🎃22 designs · Updated for 2026

Popular Traditional Pumpkin Faces

Looking for popular traditional pumpkin faces? You're in the right place. Print at 100% scale, tape it to your pumpkin, and poke through the lines with a pin.

Browse 22 designs ↓

★★★★★4.9/5from 2,400+ carvers✓ No watermark✓ Print-ready PDF

🆓

100% free

Every design is a free download. No account, no catch.

⚡

Print-ready PDF

One click to a clean PDF, pre-sized for a standard 8.5×11 sheet.

✂️

Carve tonight

Print, tape it to your pumpkin, trace the lines, and start carving.

22 popular traditional pumpkin faces

Beginner or pro, there's something on this page for you.

Easy

Diamond Nose and Three Teeth

This is the timeless jack-o'-lantern: two triangle eyes, a diamond nose, and a wide crescent grin interrupted by three blocky square teeth, one hanging from the top lip and two rising from the bottom. Everything except the teeth is cut through, with the teeth left as standing tabs of shell. It is an easy, forgiving first carve; cut toward each tooth from both sides rather than sawing across it, so the tabs never take sideways pressure.

Free PDF

Easy

Broad Grin with Five Teeth

Two chunky triangle eyes sit above a broad zigzag grin, where five blocky teeth alternate along the top and bottom of the smile. Everything cuts fully through, and the oversized features make this a great pick for a big pumpkin that needs to be seen from a distance. Carve the mouth as one long opening and leave each tooth attached to the rim, sawing the tooth notches last so they stay sturdy.

Free PDF

Intermediate

Cross With Ten Rays

A bold cross anchors the center of the design while ten tapered rays burst outward around it like beams of light. The cross and every ray are pierced through, leaving dark shell between them that frames the radiating pattern. Cut the large cross first to relieve pressure on the wall, then work each ray from its wide outer end toward the narrow tip so the points finish clean.

Free PDF

Easy

Classic Grin with Two Teeth

The timeless jack-o'-lantern: two triangle eyes, a triangle nose, and a wide curved grin interrupted by two chunky square teeth, one on top and one on the bottom. Every feature is pierced straight through for maximum glow. This easy pattern is the classic first carve; angle each triangle cut slightly toward the center of the shape so the plugs pop out cleanly, and leave the tooth blocks generous so they do not snap.

Free PDF

Intermediate

Twin Crosses Beneath Arches

Two crosses stand side by side, each framed beneath its own tall rounded arch like twin chapel windows. The arch outlines and the crosses are cut through the wall as narrow channels, so light traces the frames while the solid rind inside each arch makes the crosses read boldly. At medium difficulty the slim arch bands are the fragile part, so cut them in short segments and leave the interior panels firmly attached.

Free PDF

Easy

Tall Triangles and Broad Smile

This is the timeless jack-o'-lantern: two tall triangle eyes, a small triangle nose, and a broad crescent smile, all cut straight through the shell. With only four openings and no fragile details, it is an ideal first carve for a new pumpkin carver. Poke pilot holes at each triangle corner before sawing so your straight lines meet exactly where they should.

Free PDF

Easy

Wide Smile With One Tooth

Made for short, squat pumpkins, this low-profile face uses two simple triangle eyes and a wide shallow smile interrupted by a single square upper tooth. All three openings are pierced straight through, and the small piece count keeps it firmly in easy territory. Cut the mouth last and leave the tooth notch for the very end, slicing down each side of it so the little square stays put.

Free PDF

Easy

Long Oval Surprise Face

Two round eyes, a small triangle nose, and a tall oval mouth give this design a permanently startled expression, sized for long narrow pumpkins. Just four openings are cut through, which is why it works so well for beginners and quick porch displays. Scoop the big oval mouth in stages rather than one deep cut, and the tall shape will stay smooth from top to bottom.

Free PDF

Intermediate

Brows and Six Cheek Dots

A classic jack-o'-lantern face with slanted triangle eyes topped by separate angled brow cuts, a diamond nose, and a wide grin broken by six blocky teeth, plus three small round holes dotting each cheek. Every element is cut fully through so the whole face blazes at night. A solid medium project; drill or punch the cheek dots first while the wall is strongest, then saw the eyes, brows, and mouth.

Free PDF

Intermediate

Arched Eyes and Seven Slots

This cheerful face pairs tall arched eyes, each with a round pupil left attached at the top, with a triangle nose and a huge grin broken by seven tooth slots. The eyes, nose, and mouth are pierced while the pupils and tooth bars remain as connected shell. The attached pupils are the trickiest part, so cut around each one carefully and leave a generous bridge so they stay anchored.

Free PDF

Easy

Wide Smile on a Warty Pumpkin

Two big triangle eyes and a huge upturned crescent smile turn any bumpy heirloom pumpkin into a cheerful classic jack-o'-lantern. All three shapes are simple cut-through openings, so warts and ridges on the shell only add character around the glow. This easy pattern is perfect for a first carve; make long smooth strokes along the smile and pop each triangle out in one clean piece.

Free PDF

Easy

Peaked Eyes and Offset Teeth

A timeless porch jack-o'-lantern with peaked half-round eyes, a triangle nose, and a broad smile broken by offset square teeth on the top and bottom lip. Every element is a full cut-through, so it lights up brilliantly at dusk. Cut the mouth last and remove it in tooth-sized sections; sawing the whole smile as one piece puts stress on the little tooth tabs.

Free PDF