Similar to This
View all stencils →About this stencil
A wildly ornate astonished face: two huge round eyes split by vertical bars, a tall oval mouth gaping in shock, and a halo of diamonds, dots, and curved flourishes radiating in every direction. All of it is cut through, from the barred eyes to the smallest accent dot, so the whole pumpkin erupts in patterned light. Rated hard for its piece count, work from the center outward and leave the outer diamonds and dots for the final pass. This design is rated Advanced and takes most carvers around 150 minutes from trace to glow. Multi-layer cuts with skin-peel shading. Plan your cuts first.
Pumpkin size guide
- 🎃 Small (5–7") — print at 80%
- 🎃 Medium (7–10") — print at 100% (recommended)
- 🎃 Large (11–13") — print at 130%
- 🎃 Giant (14"+) — print at 150% on tabloid paper
Frequently asked questions
Can I resize this stencil?▾
Yes. The PDF is vector so it scales cleanly. Print at 100% for a 7–10 inch pumpkin, 130% for 11–13 inch, or 150% for a giant. Use your printer's "Fit to page" or "Custom scale" setting.
What kind of paper works best?▾
Standard 20 lb letter or A4 printer paper is fine. Heavier paper is harder to bend around the pumpkin curve. If your printer supports it, set the quality to 'best' so the lines are crisp.
How long will the carved pumpkin last?▾
Usually 5–10 days. Coat all cut surfaces with petroleum jelly and store the pumpkin somewhere cool overnight. Avoid direct sun. Battery LED pumpkin lights produce no heat and double the lifespan.
Can I sell pumpkins carved with this stencil?▾
Yes, the carved pumpkin you make is yours. The license covers personal and small-scale commercial carving (selling carved pumpkins, photographing them, posting on social). You may not resell the PDF file itself.
What if my printer doesn't print the whole stencil?▾
Set 'Page scaling' to 'Fit' in the print dialog and uncheck 'Auto-rotate'. If it still cuts off, the design includes 0.25" of safe-area margin so a small crop won't ruin it.
How to carve this stencil
- 1Print it
Download the PDF and print at 100% scale on letter or A4 paper.
- 2Prep the pumpkin
Cut the lid at an angle, scoop the guts, thin the wall to ~1 inch.
- 3Tape it on
Snip darts in the paper so it lies flat against the curve.
- 4Transfer the design
Poke along every line — about one dot every 1/8 inch.
- 5Carve it
Connect the dots with short straight cuts. Center first, work outward.
- 6Light it up
Drop in a battery LED pumpkin light and you're done.
Tools you'll need
For a advanced carve like this you'll want a linoleum cutter set, x-acto knife, peel tool, and pin transfer wheel. Here's the kit we reach for — start with whatever you already own.
Elmchee Pumpkin Carving Kit
13-piece kit with carrying case
Saws for the larger cutouts, plus a scoop for hollowing. Covers both jobs in one kit.
View on Amazon ↗
HOME MOST LED Pumpkin Lights
4-pack, battery operated, with remote + timer
Orange glow made for jack-o'-lanterns. The remote and timer light the pumpkin every evening without reaching inside.
View on Amazon ↗
Speedball 4131 Lino Cutter Set
Handle + 5 interchangeable cutters
Interchangeable cutters for peeling and shading the face. Useful for the finer details.
View on Amazon ↗
Community Pumpkin Carving Ideas
Carving ideas that use stencils like this one.
Related stencils
Carvers who liked this one also downloaded these.
IntermediateStaring Eyes and Eight Wedges
Two enormous staring eyes dominate this design, each with a pupil tab left attached at the bottom rim, a curved brow arcing above, and short wedge-shaped rays radiating around the outside like a nervous twitch of light. There is no mouth, which makes the gaze even more unsettling. In this medium carve the pupil tabs are the key detail; cut around each pupil carefully so its bridge to the lower eyelid stays at least a half inch wide.
Beginner-friendlyTwo Flasks and Five Bubbles
A triangular Erlenmeyer flask and a round boiling flask stand side by side while five bubbles of different sizes rise between and above them. Every flask body and bubble is cut straight through, so the whole experiment glows like it is mid reaction. This easy pattern only asks for patience on the small bubbles; a drill bit or corer makes those circles fast and perfectly round.
IntermediateGear Cross and Three Dots
A chunky steampunk gear glowing around a solid crossbar, with three round rivet dots floating beside it like escaping sparks. The spaces between the gear teeth and the four windows inside the cog are cut through, while the cross-shaped bar stays attached to the pumpkin wall and holds everything together. Carve the small dots first, then the gear windows, and keep the crossbar at least a finger wide so the design stays rigid.
Expert / ProSpoked Eyes and Diamond Halos
Two enormous hypnotic eyes built as spoked wheels, each iris divided by radial spokes around a glowing hub, ringed by halos of small diamond and teardrop cutouts with arched brow fans above. Every spoke gap, diamond, and teardrop is pierced individually, creating a mesmerizing lace of light. An expert carve with dozens of tiny openings; use a fine detail saw and rotate the pumpkin, not your wrist, on the curves.
Expert / ProCup, Three Dice and a Pawn
A game-night still life in deep relief: a tipped-over cup spills three pip-dotted dice across a carved tabletop while a rounded pawn stands nearby on its base. Everything is continuous-wall sculpting with no pierced holes, using multiple shaved depths to make the cup, dice faces, and pawn read as three-dimensional objects. As an expert relief carve, block in the deepest background plane first, then step each object forward in layers, cutting the tiny pips last with a round gouge.
Expert / ProRaised Brows and Oval Gasp
An ornamental surprised face: two big eyes striped with vertical bars sit beneath fanned brow lines, above a tall oval gasping mouth ringed by a halo of teardrop cutouts. Every bar, fan line, teardrop, and the central oval is pierced through, and the sheer number of narrow slits is what makes this an expert carve. Cut all the fine slits before the big oval, working outward from the center, so the wall keeps its strength as long as possible.