Similar to This
View all stencils →About this stencil
A friendly twist on the classic face: two upside-down triangle eyes over a wide crescent smile broken by a single square tooth at the top. The eyes and mouth are simple cut-through openings, and the lone tooth is just a small tab of rind left attached along the upper lip. This is a true easy carve, so it is a great first solo project for new carvers; cut the mouth in two halves on either side of the tooth so you never stress that little tab. This design is rated Beginner-friendly and takes most carvers around 30 minutes from trace to glow. Great for kids and first-timers. Big shapes, short cuts.
Pumpkin size guide
- 🎃 Small (5–7") — print at 80%
- 🎃 Medium (7–10") — print at 100% (recommended)
- 🎃 Large (11–13") — print at 130%
- 🎃 Giant (14"+) — print at 150% on tabloid paper
Frequently asked questions
Can I resize this stencil?▾
Yes. The PDF is vector so it scales cleanly. Print at 100% for a 7–10 inch pumpkin, 130% for 11–13 inch, or 150% for a giant. Use your printer's "Fit to page" or "Custom scale" setting.
What kind of paper works best?▾
Standard 20 lb letter or A4 printer paper is fine. Heavier paper is harder to bend around the pumpkin curve. If your printer supports it, set the quality to 'best' so the lines are crisp.
How long will the carved pumpkin last?▾
Usually 5–10 days. Coat all cut surfaces with petroleum jelly and store the pumpkin somewhere cool overnight. Avoid direct sun. Battery LED pumpkin lights produce no heat and double the lifespan.
Can I sell pumpkins carved with this stencil?▾
Yes, the carved pumpkin you make is yours. The license covers personal and small-scale commercial carving (selling carved pumpkins, photographing them, posting on social). You may not resell the PDF file itself.
What if my printer doesn't print the whole stencil?▾
Set 'Page scaling' to 'Fit' in the print dialog and uncheck 'Auto-rotate'. If it still cuts off, the design includes 0.25" of safe-area margin so a small crop won't ruin it.
How to carve this stencil
- 1Print it
Download the PDF and print at 100% scale on letter or A4 paper.
- 2Prep the pumpkin
Cut the lid at an angle, scoop the guts, thin the wall to ~1 inch.
- 3Tape it on
Snip darts in the paper so it lies flat against the curve.
- 4Transfer the design
Poke along every line — about one dot every 1/8 inch.
- 5Carve it
Connect the dots with short straight cuts. Center first, work outward.
- 6Light it up
Drop in a battery LED pumpkin light and you're done.
Tools you'll need
For a beginner-friendly carve like this you'll want a paring knife, spoon / scoop, marker, and led pumpkin light. Here's the kit we reach for — start with whatever you already own.
Elmchee Pumpkin Carving Kit
13-piece kit with carrying case
Saws for the larger cutouts, plus a scoop for hollowing. Covers both jobs in one kit.
View on Amazon ↗
HOME MOST LED Pumpkin Lights
4-pack, battery operated, with remote + timer
Orange glow made for jack-o'-lanterns. The remote and timer light the pumpkin every evening without reaching inside.
View on Amazon ↗
Speedball 4131 Lino Cutter Set
Handle + 5 interchangeable cutters
Interchangeable cutters for peeling and shading the face. Useful for the finer details.
View on Amazon ↗
Community Pumpkin Carving Ideas
Carving ideas that use stencils like this one.
Related stencils
Carvers who liked this one also downloaded these.
Beginner-friendlyRound Eyes and Two Short Teeth
Round eyes, a small triangle nose, and a broad grin with two stubby square teeth give this jack-o'-lantern a warm, welcoming personality. The eyes, nose, and mouth are cut through, while the two little teeth stay attached along the top of the smile. On this easy carve, cut carefully around each tooth so it remains anchored to the wall; everything else is simple circles and one flowing mouth curve.
IntermediateRound Pupils and Five Teeth
A big-eyed, grinning jack-o'-lantern face with round pupil tabs left inside each eye and five square teeth breaking up a wide smile. The eyes and mouth are cut clean through while the pupils and teeth remain attached to the rind as solid bridges. Those round pupils make this a medium carve, so pierce a relief hole beside each one first and saw toward it rather than levering the blade, which can snap the connecting tab.
IntermediateHappy Crescent-Eyed Grin
A cheerful jack-o'-lantern face with sweeping crescent eyes, a small notched nose, and a wide grin framed by two pointed fangs and blocky lower teeth. Every feature is cut fully through so the whole face glows. The crescent eyes taper to fine points, so use a thin saw and cut toward the tips from both directions to keep the corners crisp.
Beginner-friendlyClassic Snaggletooth Grin
This is the timeless jack-o'-lantern face: two bold triangle eyes, round cheek dots, a circle nose, and a wide grin broken up by chunky snaggleteeth. Every shape is cut all the way through, so the whole face glows brightly at night. Because the openings are large and simple, it is a perfect first carve; just leave the tooth tabs attached to the rim of the mouth as you saw around them.
IntermediateWink and Five Rounded Gaps
One eye is a jaunty upswept crescent wink while the other stays a wide triangle, set over a small diamond nose and a lopsided grin broken into five rounded gaps by chunky teeth. The eyes, nose, and mouth gaps are cut through, leaving the tooth shapes as attached skin between them. A medium carver should cut the five mouth gaps individually rather than one big mouth, which keeps every tooth solidly connected and the crooked smile intact.
IntermediateOval Eyes and Eight Cheek Dots
Big oval eyes sit under arched brows above a round button nose and a broad smile showing four blunt square teeth, with four freckle dots sprinkled on each cheek. The eyes, brows, nose, mouth, and dots are pierced through while the tooth bridges stay connected. Poke the eight small cheek dots first, then cut the large features, leaving the tooth bars until the end so they keep support.