Similar to This
View all stencils →About this stencil
A wide, low jack-o'-lantern face with sly almond-shaped eyes, a small triangle nose, and a long jagged mouth packed with alternating square teeth top and bottom. Everything is pierced through, and the horizontal layout suits squat, wide pumpkins. At medium difficulty the tooth row is the main work; cut the mouth's outer outline first, then remove the gaps between teeth one at a time so each block keeps support while you work. This design is rated Intermediate and takes most carvers around 75 minutes from trace to glow. Comfortable knife handling required. Small details and curves.
Pumpkin size guide
- 🎃 Small (5–7") — print at 80%
- 🎃 Medium (7–10") — print at 100% (recommended)
- 🎃 Large (11–13") — print at 130%
- 🎃 Giant (14"+) — print at 150% on tabloid paper
Frequently asked questions
Can I resize this stencil?▾
Yes. The PDF is vector so it scales cleanly. Print at 100% for a 7–10 inch pumpkin, 130% for 11–13 inch, or 150% for a giant. Use your printer's "Fit to page" or "Custom scale" setting.
What kind of paper works best?▾
Standard 20 lb letter or A4 printer paper is fine. Heavier paper is harder to bend around the pumpkin curve. If your printer supports it, set the quality to 'best' so the lines are crisp.
How long will the carved pumpkin last?▾
Usually 5–10 days. Coat all cut surfaces with petroleum jelly and store the pumpkin somewhere cool overnight. Avoid direct sun. Battery LED pumpkin lights produce no heat and double the lifespan.
Can I sell pumpkins carved with this stencil?▾
Yes, the carved pumpkin you make is yours. The license covers personal and small-scale commercial carving (selling carved pumpkins, photographing them, posting on social). You may not resell the PDF file itself.
What if my printer doesn't print the whole stencil?▾
Set 'Page scaling' to 'Fit' in the print dialog and uncheck 'Auto-rotate'. If it still cuts off, the design includes 0.25" of safe-area margin so a small crop won't ruin it.
How to carve this stencil
- 1Print it
Download the PDF and print at 100% scale on letter or A4 paper.
- 2Prep the pumpkin
Cut the lid at an angle, scoop the guts, thin the wall to ~1 inch.
- 3Tape it on
Snip darts in the paper so it lies flat against the curve.
- 4Transfer the design
Poke along every line — about one dot every 1/8 inch.
- 5Carve it
Connect the dots with short straight cuts. Center first, work outward.
- 6Light it up
Drop in a battery LED pumpkin light and you're done.
Tools you'll need
For a intermediate carve like this you'll want a x-acto knife, poker tool, ribbon scoop, and painter's tape. Here's the kit we reach for — start with whatever you already own.
Elmchee Pumpkin Carving Kit
13-piece kit with carrying case
Saws for the larger cutouts, plus a scoop for hollowing. Covers both jobs in one kit.
View on Amazon ↗
HOME MOST LED Pumpkin Lights
4-pack, battery operated, with remote + timer
Orange glow made for jack-o'-lanterns. The remote and timer light the pumpkin every evening without reaching inside.
View on Amazon ↗
Speedball 4131 Lino Cutter Set
Handle + 5 interchangeable cutters
Interchangeable cutters for peeling and shading the face. Useful for the finer details.
View on Amazon ↗
Community Pumpkin Carving Ideas
Carving ideas that use stencils like this one.
Related stencils
Carvers who liked this one also downloaded these.
IntermediateHeavy-Brow Angry Face
This scowling jack-o'-lantern glares out through heavy slanted brows, a small triangle nose, and a snarling mouth ringed with sharp fangs top and bottom. Every feature is a pierced opening, leaving thick pumpkin wall between the angry eyes and the jagged mouth for strength. At medium difficulty the narrow inner brow points are the fragile spots, so cut the eyes from the center outward and save the thin corners for last.
Beginner-friendlyDiamond Nose and Three Teeth
This is the timeless jack-o'-lantern: two triangle eyes, a diamond nose, and a wide crescent grin interrupted by three blocky square teeth, one hanging from the top lip and two rising from the bottom. Everything except the teeth is cut through, with the teeth left as standing tabs of shell. It is an easy, forgiving first carve; cut toward each tooth from both sides rather than sawing across it, so the tabs never take sideways pressure.
Beginner-friendlyBroad Grin with Five Teeth
Two chunky triangle eyes sit above a broad zigzag grin, where five blocky teeth alternate along the top and bottom of the smile. Everything cuts fully through, and the oversized features make this a great pick for a big pumpkin that needs to be seen from a distance. Carve the mouth as one long opening and leave each tooth attached to the rim, sawing the tooth notches last so they stay sturdy.
Beginner-friendlyClassic Grin with Two Teeth
The timeless jack-o'-lantern: two triangle eyes, a triangle nose, and a wide curved grin interrupted by two chunky square teeth, one on top and one on the bottom. Every feature is pierced straight through for maximum glow. This easy pattern is the classic first carve; angle each triangle cut slightly toward the center of the shape so the plugs pop out cleanly, and leave the tooth blocks generous so they do not snap.
IntermediateAngular Seven-Tooth Grin
A sharp-edged jack-o'-lantern face with slanted triangle eyes, an angular nose, and a wide jagged mouth broken into seven pointed teeth. Every shape is cut straight through the pumpkin wall, making a bright, high-contrast face that reads perfectly from the porch steps. It is a medium pattern because of the many small tooth points, so saw into each corner from both directions instead of twisting the blade to keep the tips sharp.
IntermediateBrows and Six Cheek Dots
A classic jack-o'-lantern face with slanted triangle eyes topped by separate angled brow cuts, a diamond nose, and a wide grin broken by six blocky teeth, plus three small round holes dotting each cheek. Every element is cut fully through so the whole face blazes at night. A solid medium project; drill or punch the cheek dots first while the wall is strongest, then saw the eyes, brows, and mouth.