Similar to This
View all stencils →About this stencil
One huge round eye stares while the other squeezes into a curled wink above a giant open grin packed with blocky square teeth, and freckle dots sprinkle each cheek. The eyes, mouth, and freckles all cut through the wall, with skin bridges left in place to form the teeth. Cut the mouth's outer outline first, then remove the gaps between teeth one at a time so each block stays anchored. This design is rated Intermediate and takes most carvers around 75 minutes from trace to glow. Comfortable knife handling required. Small details and curves.
Pumpkin size guide
- 🎃 Small (5–7") — print at 80%
- 🎃 Medium (7–10") — print at 100% (recommended)
- 🎃 Large (11–13") — print at 130%
- 🎃 Giant (14"+) — print at 150% on tabloid paper
Frequently asked questions
Can I resize this stencil?▾
Yes. The PDF is vector so it scales cleanly. Print at 100% for a 7–10 inch pumpkin, 130% for 11–13 inch, or 150% for a giant. Use your printer's "Fit to page" or "Custom scale" setting.
What kind of paper works best?▾
Standard 20 lb letter or A4 printer paper is fine. Heavier paper is harder to bend around the pumpkin curve. If your printer supports it, set the quality to 'best' so the lines are crisp.
How long will the carved pumpkin last?▾
Usually 5–10 days. Coat all cut surfaces with petroleum jelly and store the pumpkin somewhere cool overnight. Avoid direct sun. Battery LED pumpkin lights produce no heat and double the lifespan.
Can I sell pumpkins carved with this stencil?▾
Yes, the carved pumpkin you make is yours. The license covers personal and small-scale commercial carving (selling carved pumpkins, photographing them, posting on social). You may not resell the PDF file itself.
What if my printer doesn't print the whole stencil?▾
Set 'Page scaling' to 'Fit' in the print dialog and uncheck 'Auto-rotate'. If it still cuts off, the design includes 0.25" of safe-area margin so a small crop won't ruin it.
How to carve this stencil
- 1Print it
Download the PDF and print at 100% scale on letter or A4 paper.
- 2Prep the pumpkin
Cut the lid at an angle, scoop the guts, thin the wall to ~1 inch.
- 3Tape it on
Snip darts in the paper so it lies flat against the curve.
- 4Transfer the design
Poke along every line — about one dot every 1/8 inch.
- 5Carve it
Connect the dots with short straight cuts. Center first, work outward.
- 6Light it up
Drop in a battery LED pumpkin light and you're done.
Tools you'll need
For a intermediate carve like this you'll want a x-acto knife, poker tool, ribbon scoop, and painter's tape. Here's the kit we reach for — start with whatever you already own.
Elmchee Pumpkin Carving Kit
13-piece kit with carrying case
Saws for the larger cutouts, plus a scoop for hollowing. Covers both jobs in one kit.
View on Amazon ↗
HOME MOST LED Pumpkin Lights
4-pack, battery operated, with remote + timer
Orange glow made for jack-o'-lanterns. The remote and timer light the pumpkin every evening without reaching inside.
View on Amazon ↗
Speedball 4131 Lino Cutter Set
Handle + 5 interchangeable cutters
Interchangeable cutters for peeling and shading the face. Useful for the finer details.
View on Amazon ↗
Community Pumpkin Carving Ideas
Carving ideas that use stencils like this one.
Related stencils
Carvers who liked this one also downloaded these.
AdvancedFour Teeth and Notched Tongue
Arched brows curve over squinting eyes while a huge open mouth shows four top teeth and a notched tongue lolling below, with short laugh lines radiating from each cheek. The face is all pierced cuts, and it rates hard because the tongue and teeth stay attached by narrow tabs inside the big mouth opening. Cut the mouth outline first, then carefully notch around the tongue tab last so it does not break free.
AdvancedUnequal Eyes and Tongue Grin
This mischievous face pairs one big round eye with a smaller sly one under arched brows, above a sprawling grin full of gapped teeth and a tongue-shaped opening lolling out below. Clusters of drilled dots frame each cheek like a glowing gridwork of freckles. It is all cut-through work with many narrow tooth bridges, so use a fine saw, cut the dots first, and support each bridge as you free the mouth pieces.
IntermediateWink and Five Rounded Gaps
One eye is a jaunty upswept crescent wink while the other stays a wide triangle, set over a small diamond nose and a lopsided grin broken into five rounded gaps by chunky teeth. The eyes, nose, and mouth gaps are cut through, leaving the tooth shapes as attached skin between them. A medium carver should cut the five mouth gaps individually rather than one big mouth, which keeps every tooth solidly connected and the crooked smile intact.
IntermediateWinking Seven-Tooth Grin
A goofy winking jack-o'-lantern with one wide round eye, one squinting wink, a triangle nose, and an enormous grin broken up by a jumble of square and pointed teeth along both lips. Every feature is cut clean through so the mismatched expression beams from the whole face. At medium difficulty the mouth is the main event; cut the grin outline first, then shape each tooth individually, alternating sides so the lip strips stay supported.
Beginner-friendlyWide Grin and One Broad Tooth
Made for short, squat pumpkins, this goofy face pairs two upswept triangle eyes with an enormous grin interrupted by a single broad tooth hanging from the top lip. The eyes and mouth are cut through, and the tooth is simply a block of shell left in place inside the smile opening. Cut around the tooth carefully on both sides before removing the mouth pieces so it stays firmly attached.
Beginner-friendlyTwo Lower Teeth Smile
This cheerful jack-o'-lantern face pairs two big round eyes with a wide open grin interrupted by a pair of goofy buck teeth. The eyes and mouth are cut all the way through, while the two square teeth are left attached to the top lip. Since it is an easy carve, just take care around those teeth: cut the mouth opening around them and leave each tooth anchored so it does not snap off.