Similar to This
View all stencils →About this stencil
A big-eyed, grinning jack-o'-lantern face with round pupil tabs left inside each eye and five square teeth breaking up a wide smile. The eyes and mouth are cut clean through while the pupils and teeth remain attached to the rind as solid bridges. Those round pupils make this a medium carve, so pierce a relief hole beside each one first and saw toward it rather than levering the blade, which can snap the connecting tab. This design is rated Intermediate and takes most carvers around 75 minutes from trace to glow. Comfortable knife handling required. Small details and curves.
Pumpkin size guide
- 🎃 Small (5–7") — print at 80%
- 🎃 Medium (7–10") — print at 100% (recommended)
- 🎃 Large (11–13") — print at 130%
- 🎃 Giant (14"+) — print at 150% on tabloid paper
Frequently asked questions
Can I resize this stencil?▾
Yes. The PDF is vector so it scales cleanly. Print at 100% for a 7–10 inch pumpkin, 130% for 11–13 inch, or 150% for a giant. Use your printer's "Fit to page" or "Custom scale" setting.
What kind of paper works best?▾
Standard 20 lb letter or A4 printer paper is fine. Heavier paper is harder to bend around the pumpkin curve. If your printer supports it, set the quality to 'best' so the lines are crisp.
How long will the carved pumpkin last?▾
Usually 5–10 days. Coat all cut surfaces with petroleum jelly and store the pumpkin somewhere cool overnight. Avoid direct sun. Battery LED pumpkin lights produce no heat and double the lifespan.
Can I sell pumpkins carved with this stencil?▾
Yes, the carved pumpkin you make is yours. The license covers personal and small-scale commercial carving (selling carved pumpkins, photographing them, posting on social). You may not resell the PDF file itself.
What if my printer doesn't print the whole stencil?▾
Set 'Page scaling' to 'Fit' in the print dialog and uncheck 'Auto-rotate'. If it still cuts off, the design includes 0.25" of safe-area margin so a small crop won't ruin it.
How to carve this stencil
- 1Print it
Download the PDF and print at 100% scale on letter or A4 paper.
- 2Prep the pumpkin
Cut the lid at an angle, scoop the guts, thin the wall to ~1 inch.
- 3Tape it on
Snip darts in the paper so it lies flat against the curve.
- 4Transfer the design
Poke along every line — about one dot every 1/8 inch.
- 5Carve it
Connect the dots with short straight cuts. Center first, work outward.
- 6Light it up
Drop in a battery LED pumpkin light and you're done.
Tools you'll need
For a intermediate carve like this you'll want a x-acto knife, poker tool, ribbon scoop, and painter's tape. Here's the kit we reach for — start with whatever you already own.
Elmchee Pumpkin Carving Kit
13-piece kit with carrying case
Saws for the larger cutouts, plus a scoop for hollowing. Covers both jobs in one kit.
View on Amazon ↗
HOME MOST LED Pumpkin Lights
4-pack, battery operated, with remote + timer
Orange glow made for jack-o'-lanterns. The remote and timer light the pumpkin every evening without reaching inside.
View on Amazon ↗
Speedball 4131 Lino Cutter Set
Handle + 5 interchangeable cutters
Interchangeable cutters for peeling and shading the face. Useful for the finer details.
View on Amazon ↗
Community Pumpkin Carving Ideas
Carving ideas that use stencils like this one.
Related stencils
Carvers who liked this one also downloaded these.
IntermediateHappy Crescent-Eyed Grin
A cheerful jack-o'-lantern face with sweeping crescent eyes, a small notched nose, and a wide grin framed by two pointed fangs and blocky lower teeth. Every feature is cut fully through so the whole face glows. The crescent eyes taper to fine points, so use a thin saw and cut toward the tips from both directions to keep the corners crisp.
IntermediateOval Eyes and Eight Cheek Dots
Big oval eyes sit under arched brows above a round button nose and a broad smile showing four blunt square teeth, with four freckle dots sprinkled on each cheek. The eyes, brows, nose, mouth, and dots are pierced through while the tooth bridges stay connected. Poke the eight small cheek dots first, then cut the large features, leaving the tooth bars until the end so they keep support.
Beginner-friendlyCrescent Eyes and Curved Smile
Pure cheer: two upturned crescent eyes squint with delight above a huge toothless smile that curls up at both corners. All three shapes are pierced through so the whole face beams with candlelight, and the matching curves give it a warm, laughing character. This easy pattern rewards smooth cutting; saw each crescent in one steady motion following the curve, and round off the smile's corners rather than leaving sharp points.
Beginner-friendlyRound Eyes and Two Short Teeth
Round eyes, a small triangle nose, and a broad grin with two stubby square teeth give this jack-o'-lantern a warm, welcoming personality. The eyes, nose, and mouth are cut through, while the two little teeth stay attached along the top of the smile. On this easy carve, cut carefully around each tooth so it remains anchored to the wall; everything else is simple circles and one flowing mouth curve.
Beginner-friendlyLeaning Eyes and Square Teeth
The timeless jack-o'-lantern: two leaning triangle eyes, a triangle nose, and a huge crescent grin interrupted by two blocky square teeth, one up and one down. Everything is a straightforward cut-through, which is exactly why this face has been a first-timer favorite for generations. Cut the mouth last and leave the tooth tabs generous; you can always trim a tooth thinner, but you cannot put pumpkin back.
Beginner-friendlyTall Triangles and Twin Teeth
The timeless jack-o'-lantern: two tall triangle eyes, a smaller triangle nose, and a wide friendly smile interrupted by two blocky teeth, one dropping from the top lip and one rising from the bottom. All four shapes are cut straight through for that classic warm glow. This easy pattern is ideal for a child's first supervised carve; make each triangle in three straight cuts and push the pieces out from inside the pumpkin.