Similar to This
View all stencils →About this stencil
This snarling jack-o'-lantern glares through slanted, angry eyes above a flared triangular nose and a huge split mouth bristling with long fangs and jagged lower teeth. The eyes, nose, and mouth are all cut through, while thin skin bridges hold each fang in place against the glow. Rated hard because of those narrow tooth bridges; carve the fangs last with a fine saw and leave extra width until the final pass. This design is rated Advanced and takes most carvers around 150 minutes from trace to glow. Multi-layer cuts with skin-peel shading. Plan your cuts first.
Pumpkin size guide
- 🎃 Small (5–7") — print at 80%
- 🎃 Medium (7–10") — print at 100% (recommended)
- 🎃 Large (11–13") — print at 130%
- 🎃 Giant (14"+) — print at 150% on tabloid paper
Frequently asked questions
Can I resize this stencil?▾
Yes. The PDF is vector so it scales cleanly. Print at 100% for a 7–10 inch pumpkin, 130% for 11–13 inch, or 150% for a giant. Use your printer's "Fit to page" or "Custom scale" setting.
What kind of paper works best?▾
Standard 20 lb letter or A4 printer paper is fine. Heavier paper is harder to bend around the pumpkin curve. If your printer supports it, set the quality to 'best' so the lines are crisp.
How long will the carved pumpkin last?▾
Usually 5–10 days. Coat all cut surfaces with petroleum jelly and store the pumpkin somewhere cool overnight. Avoid direct sun. Battery LED pumpkin lights produce no heat and double the lifespan.
Can I sell pumpkins carved with this stencil?▾
Yes, the carved pumpkin you make is yours. The license covers personal and small-scale commercial carving (selling carved pumpkins, photographing them, posting on social). You may not resell the PDF file itself.
What if my printer doesn't print the whole stencil?▾
Set 'Page scaling' to 'Fit' in the print dialog and uncheck 'Auto-rotate'. If it still cuts off, the design includes 0.25" of safe-area margin so a small crop won't ruin it.
How to carve this stencil
- 1Print it
Download the PDF and print at 100% scale on letter or A4 paper.
- 2Prep the pumpkin
Cut the lid at an angle, scoop the guts, thin the wall to ~1 inch.
- 3Tape it on
Snip darts in the paper so it lies flat against the curve.
- 4Transfer the design
Poke along every line — about one dot every 1/8 inch.
- 5Carve it
Connect the dots with short straight cuts. Center first, work outward.
- 6Light it up
Drop in a battery LED pumpkin light and you're done.
Tools you'll need
For a advanced carve like this you'll want a linoleum cutter set, x-acto knife, peel tool, and pin transfer wheel. Here's the kit we reach for — start with whatever you already own.
Elmchee Pumpkin Carving Kit
13-piece kit with carrying case
Saws for the larger cutouts, plus a scoop for hollowing. Covers both jobs in one kit.
View on Amazon ↗
HOME MOST LED Pumpkin Lights
4-pack, battery operated, with remote + timer
Orange glow made for jack-o'-lanterns. The remote and timer light the pumpkin every evening without reaching inside.
View on Amazon ↗
Speedball 4131 Lino Cutter Set
Handle + 5 interchangeable cutters
Interchangeable cutters for peeling and shading the face. Useful for the finer details.
View on Amazon ↗
Community Pumpkin Carving Ideas
Carving ideas that use stencils like this one.
Related stencils
Carvers who liked this one also downloaded these.
Beginner-friendlySlanted Eyes and Twin Fangs
A sinister face with narrow slanted eyes, a slim angled nose, and a wide sneering mouth bristling with pointed fangs top and bottom. Eyes, nose, and mouth are pierced clean through, with the fang shapes left as solid teeth jutting into the glowing opening. Even though it rates easy, the fang tips are fragile; cut each tooth from base to point and let the waste fall away instead of pulling it free.
Expert / ProLong-Eared Monster Face
A tall, unsettling monster mask stares out of the pumpkin: long upright ears branching like antlers, hollow ringed eyes, a skeletal snout, and a mouthful of pointed fangs, all drawn in thin interlocking cutouts. The entire face is pierced through as a network of narrow slots that leaves delicate pumpkin bridges between every glowing line. This expert design demands a fine-detail saw; carve from the center outward so the fragile bridges keep support as long as possible.
Beginner-friendlySlanted Eyes and Twin Fangs
A wicked jack-o'-lantern with sharply slanted eyes, a small triangle nose, and a curling grin pierced by two long fangs hanging from the upper lip. All the features cut straight through, and the fangs read as solid pumpkin left inside the glowing mouth opening. It is an easy carve overall; just remember the fangs are attached only at the top, so slice along their sides gently and never lever the knife against them.
AdvancedDouble Zigzag Flame Face
Jagged flame-shaped eyes glare above a huge zigzag grin packed with two rows of interlocking pointed teeth. Every eye, brow flick, and tooth gap is pierced clean through, leaving thin orange spikes of rind that read as fangs when the candle is lit. Those narrow tooth points are fragile, so cut them last, work from the tips inward, and support each spike with your free hand as you finish.
Expert / ProUnequal Eyes and Jagged Grin
A nightmare grin stretches ear to ear, packed with dozens of jagged interlocking fangs, beneath two mismatched eyes, one wide and wild and one narrowed and crossed by scar lines, with flame like spikes radiating outward and diamond accents above and below. Nearly all of it is pierced through, leaving a web of thin rind spikes that demands real patience. Work from the center of the mouth outward with a fine saw, supporting each fragile spike as you free it on this expert carve.
IntermediateAngled Eyes and Seven Fangs
Two sharply slanted triangle eyes glare above a wide jagged mouth lined with seven pointed fangs, giving this face a classic menacing snarl. Every element is cut fully through, and the zigzag mouth does most of the work, so accuracy there pays off. Cut each tooth as two separate straight strokes meeting at the point instead of dragging the saw around the corner, and the grin stays razor sharp.