Similar to This
View all stencils →About this stencil
A tall, friendly face made of just three shapes: two upright oval eyes and one deep crescent smile sweeping nearly the full width of the pumpkin. All three openings are pierced through, and the design especially suits oblong or elongated pumpkins. It is an easy carve with big forgiving shapes; cut the wide smile in two halves that meet at the center bottom so the long curve stays smooth and the flap comes out in manageable pieces. This design is rated Beginner-friendly and takes most carvers around 30 minutes from trace to glow. Great for kids and first-timers. Big shapes, short cuts.
Pumpkin size guide
- 🎃 Small (5–7") — print at 80%
- 🎃 Medium (7–10") — print at 100% (recommended)
- 🎃 Large (11–13") — print at 130%
- 🎃 Giant (14"+) — print at 150% on tabloid paper
Frequently asked questions
Can I resize this stencil?▾
Yes. The PDF is vector so it scales cleanly. Print at 100% for a 7–10 inch pumpkin, 130% for 11–13 inch, or 150% for a giant. Use your printer's "Fit to page" or "Custom scale" setting.
What kind of paper works best?▾
Standard 20 lb letter or A4 printer paper is fine. Heavier paper is harder to bend around the pumpkin curve. If your printer supports it, set the quality to 'best' so the lines are crisp.
How long will the carved pumpkin last?▾
Usually 5–10 days. Coat all cut surfaces with petroleum jelly and store the pumpkin somewhere cool overnight. Avoid direct sun. Battery LED pumpkin lights produce no heat and double the lifespan.
Can I sell pumpkins carved with this stencil?▾
Yes, the carved pumpkin you make is yours. The license covers personal and small-scale commercial carving (selling carved pumpkins, photographing them, posting on social). You may not resell the PDF file itself.
What if my printer doesn't print the whole stencil?▾
Set 'Page scaling' to 'Fit' in the print dialog and uncheck 'Auto-rotate'. If it still cuts off, the design includes 0.25" of safe-area margin so a small crop won't ruin it.
How to carve this stencil
This is a cut-through stencil: the dark numbered regions on the printable pattern are the pieces you remove, and everything white stays attached. The numbers give you the safest carving order, and the steps below walk through them one by one. Plan on about 35-50 minutes from print to candle.
Set up first. Print the PDF at 100% scale on letter or A4 paper. Cut the lid at an angle, scoop the pumpkin clean, and thin the carving wall to about 1 inch where the design will sit. Tape the pattern on (snip small darts in the paper so it hugs the curve) and transfer every outline by poking dots along the lines, about one every 1/8 inch. Peel the paper away and carve dot to dot with short, straight strokes.
Carving order
- Open the two tall oval eyes. Cut both regions marked 1. Preserve their long vertical shapes and the slightly higher right eye. Leave the broad white bridge between them intact.
- Follow the deep crescent. Cut region 2 around the broad toothless smile. Preserve the higher right corner, shallow upper arc and deep rounded lower curve. Keep the white band below the eyes untouched and support the plug before releasing its final edge.
Clear loose fibers out of each opening as you go, and never twist or pry the blade against the shell; back it out and recut instead. When every region is open, wipe the cut edges dry and drop in a battery LED puck.
Tools you'll need
For a beginner-friendly carve like this you'll want a paring knife, spoon / scoop, marker, and led pumpkin light. Here's the kit we reach for — start with whatever you already own.
Elmchee Pumpkin Carving Kit
13-piece kit with carrying case
Saws for the larger cutouts, plus a scoop for hollowing. Covers both jobs in one kit.
View on Amazon ↗
HOME MOST LED Pumpkin Lights
4-pack, battery operated, with remote + timer
Orange glow made for jack-o'-lanterns. The remote and timer light the pumpkin every evening without reaching inside.
View on Amazon ↗
Speedball 4131 Lino Cutter Set
Handle + 5 interchangeable cutters
Interchangeable cutters for peeling and shading the face. Useful for the finer details.
View on Amazon ↗
Community Pumpkin Carving Ideas
Carving ideas that use stencils like this one.
Related stencils
Carvers who liked this one also downloaded these.
Beginner-friendlyCrescent Eyes and Curved Smile
Pure cheer: two upturned crescent eyes squint with delight above a huge toothless smile that curls up at both corners. All three shapes are pierced through so the whole face beams with candlelight, and the matching curves give it a warm, laughing character. This easy pattern rewards smooth cutting; saw each crescent in one steady motion following the curve, and round off the smile's corners rather than leaving sharp points.
Beginner-friendlyTall Triangles and Twin Teeth
The timeless jack-o'-lantern: two tall triangle eyes, a smaller triangle nose, and a wide friendly smile interrupted by two blocky teeth, one dropping from the top lip and one rising from the bottom. All four shapes are cut straight through for that classic warm glow. This easy pattern is ideal for a child's first supervised carve; make each triangle in three straight cuts and push the pieces out from inside the pumpkin.
Beginner-friendlyGiant Nose and One Tooth
A big-hearted face dominated by an oversized triangle nose, flanked by two small round eyes, with a wide crescent smile carrying one square tooth. Every feature is cut through, and the giant nose becomes the brightest window on the whole pumpkin once the candle goes in. An easy pattern with generous shapes; cut the huge nose last so the wall keeps its strength while you work.
Beginner-friendlyTall Triangles and Broad Smile
This is the timeless jack-o'-lantern: two tall triangle eyes, a small triangle nose, and a broad crescent smile, all cut straight through the shell. With only four openings and no fragile details, it is an ideal first carve for a new pumpkin carver. Poke pilot holes at each triangle corner before sawing so your straight lines meet exactly where they should.
Beginner-friendlySmall Triangle-Eyed Smile
Made with small pumpkins in mind, this cheerful face uses two modest triangle eyes and a single wide crescent smile with no teeth to fuss over. All three shapes are cut straight through, giving a warm, friendly glow from even a tabletop-sized pumpkin. It is one of the easiest carves on the site; on a small pumpkin, use a thin serrated saw and cut the smile from the center outward so the thin curve stays even.
Beginner-friendlyPeaked Eyes and Offset Teeth
A timeless porch jack-o'-lantern with peaked half-round eyes, a triangle nose, and a broad smile broken by offset square teeth on the top and bottom lip. Every element is a full cut-through, so it lights up brilliantly at dusk. Cut the mouth last and remove it in tooth-sized sections; sawing the whole smile as one piece puts stress on the little tooth tabs.