Similar to This
View all stencils →About this stencil
A large eight point star anchors the center while small diamonds and dots scatter around it like a burst of night sky sparkle. Every shape is a clean cut-through opening, so the pumpkin throws star shaped light across nearby walls and steps. Cut the big star's inner corners with a fine blade and pop the little diamonds out gently to keep their sharp points intact on this medium pattern. This design is rated Intermediate and takes most carvers around 75 minutes from trace to glow. Comfortable knife handling required. Small details and curves.
Pumpkin size guide
- 🎃 Small (5–7") — print at 80%
- 🎃 Medium (7–10") — print at 100% (recommended)
- 🎃 Large (11–13") — print at 130%
- 🎃 Giant (14"+) — print at 150% on tabloid paper
Frequently asked questions
Can I resize this stencil?▾
Yes. The PDF is vector so it scales cleanly. Print at 100% for a 7–10 inch pumpkin, 130% for 11–13 inch, or 150% for a giant. Use your printer's "Fit to page" or "Custom scale" setting.
What kind of paper works best?▾
Standard 20 lb letter or A4 printer paper is fine. Heavier paper is harder to bend around the pumpkin curve. If your printer supports it, set the quality to 'best' so the lines are crisp.
How long will the carved pumpkin last?▾
Usually 5–10 days. Coat all cut surfaces with petroleum jelly and store the pumpkin somewhere cool overnight. Avoid direct sun. Battery LED pumpkin lights produce no heat and double the lifespan.
Can I sell pumpkins carved with this stencil?▾
Yes, the carved pumpkin you make is yours. The license covers personal and small-scale commercial carving (selling carved pumpkins, photographing them, posting on social). You may not resell the PDF file itself.
What if my printer doesn't print the whole stencil?▾
Set 'Page scaling' to 'Fit' in the print dialog and uncheck 'Auto-rotate'. If it still cuts off, the design includes 0.25" of safe-area margin so a small crop won't ruin it.
How to carve this stencil
- 1Print it
Download the PDF and print at 100% scale on letter or A4 paper.
- 2Prep the pumpkin
Cut the lid at an angle, scoop the guts, thin the wall to ~1 inch.
- 3Tape it on
Snip darts in the paper so it lies flat against the curve.
- 4Transfer the design
Poke along every line — about one dot every 1/8 inch.
- 5Carve it
Connect the dots with short straight cuts. Center first, work outward.
- 6Light it up
Drop in a battery LED pumpkin light and you're done.
Tools you'll need
For a intermediate carve like this you'll want a x-acto knife, poker tool, ribbon scoop, and painter's tape. Here's the kit we reach for — start with whatever you already own.
Elmchee Pumpkin Carving Kit
13-piece kit with carrying case
Saws for the larger cutouts, plus a scoop for hollowing. Covers both jobs in one kit.
View on Amazon ↗
HOME MOST LED Pumpkin Lights
4-pack, battery operated, with remote + timer
Orange glow made for jack-o'-lanterns. The remote and timer light the pumpkin every evening without reaching inside.
View on Amazon ↗
Speedball 4131 Lino Cutter Set
Handle + 5 interchangeable cutters
Interchangeable cutters for peeling and shading the face. Useful for the finer details.
View on Amazon ↗
Community Pumpkin Carving Ideas
Carving ideas that use stencils like this one.
Related stencils
Carvers who liked this one also downloaded these.
Beginner-friendlyStar & Four Dots
One big five-pointed star sits at the center of the pumpkin, ringed by four round polka-dot holes above, below, and to each side. Every shape is cut fully through, turning the pumpkin into a cheerful lantern that throws star and dot patterns onto nearby walls. This easy design is a great first carve; drill or scoop the four circles first, then saw the star point to point so the tips stay sharp.
IntermediateFive Star Band and Ten Circles
Designed for a long pumpkin lying on its side, this pattern runs a band of five bold stars across the middle with ten round holes scattered above and below like floating orbs. Every star and circle is a simple cut-through, and the sideways layout makes it a fun tabletop centerpiece instead of an upright face. At medium difficulty the stars are the focus: poke each star's five points before cutting so the angles meet sharply.
IntermediateSix Stars and Seven Dots
Six five-pointed stars and seven round dots scatter across the pumpkin like glowing confetti, wrapping around the sides rather than clustering on one face. Every star and dot is cut fully through, turning the whole pumpkin into a lantern that throws starlight in all directions. This medium all-over pattern is extra charming on a warty or bumpy pumpkin; drill the dots first, then cut each star point to point, rotating the pumpkin so you always saw at a comfortable angle.
IntermediateEight Teardrops Around Circle
Eight teardrop petals radiate around a central circle cutout, like a glowing daisy or sunburst wheel. Every teardrop and the center are pierced clean through, turning the pumpkin into a lantern that throws petal-shaped light across the porch. Cut the center circle first as your anchor point, then work around the ring, alternating sides so the wall stays balanced as you go.
IntermediateStar Above Two Chevrons
A six-point badge star shines above two stacked chevron stripes, with three small dots arcing over the top like a crest. Every shape is cut fully through the wall, giving the design the crisp look of a service badge or rank insignia glowing on the porch. Cut the chevrons from their outer ends toward the center points, and keep the rind strip between the two stripes intact for a clean military edge.
IntermediateSeven Unequal Honeycomb Cells
Seven hexagonal honeycomb cells of slightly different sizes cluster together, each one a glowing six-sided window separated by thick shared walls. Every cell is cut fully through, and those chunky connecting walls are what keep the pumpkin strong, so resist the urge to slim them down. Cut each hexagon side as its own straight stroke, finishing the corners cleanly with the knife tip, and start with the center cell to anchor the layout.