Similar to This
View all stencils →About this stencil
A classic angry jack-o'-lantern face with two sharp slanted eyes, a split two-part nose, and a jagged zigzag frown of pointed teeth. All five openings are cut straight through the wall, leaving the rest of the pumpkin untouched for maximum contrast. It is an easy pattern with only a handful of pieces, so take your time on the zigzag mouth and cut each tooth point cleanly before pushing the waste piece out. This design is rated Beginner-friendly and takes most carvers around 30 minutes from trace to glow. Great for kids and first-timers. Big shapes, short cuts.
Pumpkin size guide
- 🎃 Small (5–7") — print at 80%
- 🎃 Medium (7–10") — print at 100% (recommended)
- 🎃 Large (11–13") — print at 130%
- 🎃 Giant (14"+) — print at 150% on tabloid paper
Frequently asked questions
Can I resize this stencil?▾
Yes. The PDF is vector so it scales cleanly. Print at 100% for a 7–10 inch pumpkin, 130% for 11–13 inch, or 150% for a giant. Use your printer's "Fit to page" or "Custom scale" setting.
What kind of paper works best?▾
Standard 20 lb letter or A4 printer paper is fine. Heavier paper is harder to bend around the pumpkin curve. If your printer supports it, set the quality to 'best' so the lines are crisp.
How long will the carved pumpkin last?▾
Usually 5–10 days. Coat all cut surfaces with petroleum jelly and store the pumpkin somewhere cool overnight. Avoid direct sun. Battery LED pumpkin lights produce no heat and double the lifespan.
Can I sell pumpkins carved with this stencil?▾
Yes, the carved pumpkin you make is yours. The license covers personal and small-scale commercial carving (selling carved pumpkins, photographing them, posting on social). You may not resell the PDF file itself.
What if my printer doesn't print the whole stencil?▾
Set 'Page scaling' to 'Fit' in the print dialog and uncheck 'Auto-rotate'. If it still cuts off, the design includes 0.25" of safe-area margin so a small crop won't ruin it.
How to carve this stencil
- 1Print it
Download the PDF and print at 100% scale on letter or A4 paper.
- 2Prep the pumpkin
Cut the lid at an angle, scoop the guts, thin the wall to ~1 inch.
- 3Tape it on
Snip darts in the paper so it lies flat against the curve.
- 4Transfer the design
Poke along every line — about one dot every 1/8 inch.
- 5Carve it
Connect the dots with short straight cuts. Center first, work outward.
- 6Light it up
Drop in a battery LED pumpkin light and you're done.
Tools you'll need
For a beginner-friendly carve like this you'll want a paring knife, spoon / scoop, marker, and led pumpkin light. Here's the kit we reach for — start with whatever you already own.
Elmchee Pumpkin Carving Kit
13-piece kit with carrying case
Saws for the larger cutouts, plus a scoop for hollowing. Covers both jobs in one kit.
View on Amazon ↗
HOME MOST LED Pumpkin Lights
4-pack, battery operated, with remote + timer
Orange glow made for jack-o'-lanterns. The remote and timer light the pumpkin every evening without reaching inside.
View on Amazon ↗
Speedball 4131 Lino Cutter Set
Handle + 5 interchangeable cutters
Interchangeable cutters for peeling and shading the face. Useful for the finer details.
View on Amazon ↗
Community Pumpkin Carving Ideas
Carving ideas that use stencils like this one.
Related stencils
Carvers who liked this one also downloaded these.
IntermediateAngry Sawtooth Grin
A fierce take on the traditional jack-o'-lantern, this design pairs sharply slanted triangle eyes with a long sawtooth mouth that zigzags across the lower face. Both eyes and the jagged grin are pierced completely through the wall so the whole snarl blazes with candlelight. The narrow zigzag points make this a medium carve; cut each tooth with short strokes toward the point so the tips stay crisp instead of snapping off.
IntermediateAngled Eyes and Seven Fangs
Two sharply slanted triangle eyes glare above a wide jagged mouth lined with seven pointed fangs, giving this face a classic menacing snarl. Every element is cut fully through, and the zigzag mouth does most of the work, so accuracy there pays off. Cut each tooth as two separate straight strokes meeting at the point instead of dragging the saw around the corner, and the grin stays razor sharp.
Beginner-friendlySlant Brows and Triangle Eyes
Pure menace in four cuts: two big triangle eyes slanted inward in a hard glare, each topped by a thin detached brow slit angled the same way. All four shapes are cut through, and with no mouth at all the silent stare does the work. This is one of the easiest designs to carve and one of the most effective; keep the brow slits narrow and parallel to the eye tops so the angry angle stays sharp.
IntermediateAngular Seven-Tooth Grin
A sharp-edged jack-o'-lantern face with slanted triangle eyes, an angular nose, and a wide jagged mouth broken into seven pointed teeth. Every shape is cut straight through the pumpkin wall, making a bright, high-contrast face that reads perfectly from the porch steps. It is a medium pattern because of the many small tooth points, so saw into each corner from both directions instead of twisting the blade to keep the tips sharp.
AdvancedHeavy Brows and Stitched Smile
Sharp slanted eyes glare from under heavy brows above a narrow triangle nose and a long menacing grin lined with thin vertical teeth. The eyes, nose, and mouth are cut through, and the row of skinny tooth bridges is what earns the hard rating. Cut the mouth outline first, then remove the gaps between teeth one at a time so the fragile strips never take sideways pressure.
IntermediateNotched Brows and Jagged Grin
A characterful jack-o'-lantern with heavy notched brows sitting over sly almond eyes, and a huge open mouth whose top edge is a row of jagged zigzag teeth above a broad curling lower lip. Eyes, brow slits, and the mouth are all pierced through for a bright, expressive glow. At medium difficulty, the key move is cutting each zigzag tooth point cleanly; slice into every corner from both directions instead of turning the blade.