Similar to This
View all stencils →About this stencil
A bubbling witch's cauldron sends three curling plumes of steam up the pumpkin's face, all rendered in carved shading rather than pierced holes. You shave the skin to different depths so the pot, bubbles, and smoke glow in layered tones while the wall stays fully intact. Work the steam swirls shallow and the cauldron mouth deepest to get that lit-from-within brew effect. This design is rated Advanced and takes most carvers around 150 minutes from trace to glow. Multi-layer cuts with skin-peel shading. Plan your cuts first.
Pumpkin size guide
- 🎃 Small (5–7") — print at 80%
- 🎃 Medium (7–10") — print at 100% (recommended)
- 🎃 Large (11–13") — print at 130%
- 🎃 Giant (14"+) — print at 150% on tabloid paper
Frequently asked questions
Can I resize this stencil?▾
Yes. The PDF is vector so it scales cleanly. Print at 100% for a 7–10 inch pumpkin, 130% for 11–13 inch, or 150% for a giant. Use your printer's "Fit to page" or "Custom scale" setting.
What kind of paper works best?▾
Standard 20 lb letter or A4 printer paper is fine. Heavier paper is harder to bend around the pumpkin curve. If your printer supports it, set the quality to 'best' so the lines are crisp.
How long will the carved pumpkin last?▾
Usually 5–10 days. Coat all cut surfaces with petroleum jelly and store the pumpkin somewhere cool overnight. Avoid direct sun. Battery LED pumpkin lights produce no heat and double the lifespan.
Can I sell pumpkins carved with this stencil?▾
Yes, the carved pumpkin you make is yours. The license covers personal and small-scale commercial carving (selling carved pumpkins, photographing them, posting on social). You may not resell the PDF file itself.
What if my printer doesn't print the whole stencil?▾
Set 'Page scaling' to 'Fit' in the print dialog and uncheck 'Auto-rotate'. If it still cuts off, the design includes 0.25" of safe-area margin so a small crop won't ruin it.
How to carve this stencil
- 1Print it
Download the PDF and print at 100% scale on letter or A4 paper.
- 2Prep the pumpkin
Cut the lid at an angle, scoop the guts, thin the wall to ~1 inch.
- 3Tape it on
Snip darts in the paper so it lies flat against the curve.
- 4Transfer the design
Poke along every line — about one dot every 1/8 inch.
- 5Carve it
Connect the dots with short straight cuts. Center first, work outward.
- 6Light it up
Drop in a battery LED pumpkin light and you're done.
Tools you'll need
For a advanced carve like this you'll want a linoleum cutter set, x-acto knife, peel tool, and pin transfer wheel. Here's the kit we reach for — start with whatever you already own.
Elmchee Pumpkin Carving Kit
13-piece kit with carrying case
Saws for the larger cutouts, plus a scoop for hollowing. Covers both jobs in one kit.
View on Amazon ↗
HOME MOST LED Pumpkin Lights
4-pack, battery operated, with remote + timer
Orange glow made for jack-o'-lanterns. The remote and timer light the pumpkin every evening without reaching inside.
View on Amazon ↗
Speedball 4131 Lino Cutter Set
Handle + 5 interchangeable cutters
Interchangeable cutters for peeling and shading the face. Useful for the finer details.
View on Amazon ↗
Community Pumpkin Carving Ideas
Carving ideas that use stencils like this one.
Related stencils
Carvers who liked this one also downloaded these.
Beginner-friendlyCauldron and Three Bubbles
A round-bellied witch's cauldron with side handles and little legs, carved as one big glowing cutout, while three round bubble holes rise above the rim like escaping brew. Everything cuts fully through, so the pot blazes and the bubbles float as bright dots. One of the easiest spooky designs going; punch the three bubbles first, then saw the cauldron body in sections, leaving the handle nubs attached to the main opening.
Expert / ProWitch Profile & Clawed Hands
A wicked witch in profile fills a glowing full-moon circle, her pointed hat, hooked nose, jutting chin, and two gnarled clawed hands all left in silhouette against the light. The moon disc is cut through around her, so every detail depends on the pumpkin you leave behind. This expert design demands patience: remove the background in small wedges and never lever your blade against the thin fingers, which are the most fragile part.
Expert / ProWitch with Flaming Staff Pumpkin Stencil
A robed witch figure stands holding a tall staff topped with a flame in this expert pumpkin stencil, her pointed hat bearing a spiral curl at the tip and wisps of energy trailing her cloak and pooling at her feet. The design reads as a solid silhouette with strategic interior cuts for the face, flame, and cloak detail, so candlelight halos the entire figure while the fine interior strips glow separately. Keep the narrow bridge connecting the flame to the staff intact until last, as it is the most likely point to snap under blade pressure.
Expert / ProBubbling Witch Cauldron Pumpkin Stencil
A round-bellied witch's cauldron sits on a small tripod base while a large plume of swirling smoke and flame rises above it, branching into curling tendrils with scattered circular bubble cutouts floating free in this witch pumpkin stencil. The cauldron interior is a large open void, the smoke tendrils are narrow pierced ribbons, and each bubble is a tiny individual circle punched through the skin. Cut the cauldron body first, then remove the larger smoke ribbons; leave the small bubble circles for last and use a round drill bit or small gouge to keep them clean.
Beginner-friendlyWitch Cauldron Pumpkin Stencil
A witch's cauldron viewed straight on forms this easy witch pumpkin stencil, with three bubble circles floating above the pot, a wide rectangular opening for the cauldron mouth, a thick rim strip, and two claw-footed legs flanking a centered spout at the base. All the shapes are cut through as separate open pieces, glowing independently when lit to suggest a bubbling brew. Cut the three small bubble circles near the top of the design first, since they sit in isolation and are easiest to control before the larger cuts below loosen the wall.
Expert / ProNatural Bat with Spread Wings
A lifelike bat spreads its wings across the entire pumpkin, with big upright ears, a furry textured body, and scalloped wing membranes ribbed by long finger bones. Nothing is cut through; the whole animal is sculpted in relief by shaving the background away and layering shallow cuts for fur and wing veins. This expert design is a true sculpting project, so work with gouges and a paring knife, establish the outline first, and build the fur texture with hundreds of short flicking strokes.