Similar to This
View all stencils →About this stencil
A goofy clown face with big round eyes crossed by horizontal rind bars, teardrop shapes dangling from each cheek, a button nose, and a huge grin with three chunky teeth. The eyes, tears, nose, and mouth are all cut through, while the eye bars and teeth stay as attached rind bridges. Those bars make it a medium carve: cut each eye as an upper and lower opening on either side of the bar, supporting the bridge with a finger as you finish the strokes. This design is rated Intermediate and takes most carvers around 75 minutes from trace to glow. Comfortable knife handling required. Small details and curves.
Pumpkin size guide
- 🎃 Small (5–7") — print at 80%
- 🎃 Medium (7–10") — print at 100% (recommended)
- 🎃 Large (11–13") — print at 130%
- 🎃 Giant (14"+) — print at 150% on tabloid paper
Frequently asked questions
Can I resize this stencil?▾
Yes. The PDF is vector so it scales cleanly. Print at 100% for a 7–10 inch pumpkin, 130% for 11–13 inch, or 150% for a giant. Use your printer's "Fit to page" or "Custom scale" setting.
What kind of paper works best?▾
Standard 20 lb letter or A4 printer paper is fine. Heavier paper is harder to bend around the pumpkin curve. If your printer supports it, set the quality to 'best' so the lines are crisp.
How long will the carved pumpkin last?▾
Usually 5–10 days. Coat all cut surfaces with petroleum jelly and store the pumpkin somewhere cool overnight. Avoid direct sun. Battery LED pumpkin lights produce no heat and double the lifespan.
Can I sell pumpkins carved with this stencil?▾
Yes, the carved pumpkin you make is yours. The license covers personal and small-scale commercial carving (selling carved pumpkins, photographing them, posting on social). You may not resell the PDF file itself.
What if my printer doesn't print the whole stencil?▾
Set 'Page scaling' to 'Fit' in the print dialog and uncheck 'Auto-rotate'. If it still cuts off, the design includes 0.25" of safe-area margin so a small crop won't ruin it.
How to carve this stencil
- 1Print it
Download the PDF and print at 100% scale on letter or A4 paper.
- 2Prep the pumpkin
Cut the lid at an angle, scoop the guts, thin the wall to ~1 inch.
- 3Tape it on
Snip darts in the paper so it lies flat against the curve.
- 4Transfer the design
Poke along every line — about one dot every 1/8 inch.
- 5Carve it
Connect the dots with short straight cuts. Center first, work outward.
- 6Light it up
Drop in a battery LED pumpkin light and you're done.
Tools you'll need
For a intermediate carve like this you'll want a x-acto knife, poker tool, ribbon scoop, and painter's tape. Here's the kit we reach for — start with whatever you already own.
Elmchee Pumpkin Carving Kit
13-piece kit with carrying case
Saws for the larger cutouts, plus a scoop for hollowing. Covers both jobs in one kit.
View on Amazon ↗
HOME MOST LED Pumpkin Lights
4-pack, battery operated, with remote + timer
Orange glow made for jack-o'-lanterns. The remote and timer light the pumpkin every evening without reaching inside.
View on Amazon ↗
Speedball 4131 Lino Cutter Set
Handle + 5 interchangeable cutters
Interchangeable cutters for peeling and shading the face. Useful for the finer details.
View on Amazon ↗
Community Pumpkin Carving Ideas
Carving ideas that use stencils like this one.
Related stencils
Carvers who liked this one also downloaded these.
AdvancedGoofy Pupils and Twelve Dots
A freckle-faced goofball with lifted eyebrow cuts, big eyes crossed by full-width pupil tabs, a round nose, twelve freckle dots, and a huge open grin with mismatched teeth. The openings are cut through while the pupil bars, teeth, and surrounding freckle rind stay intact. It rates hard because those wide pupil tabs span the entire eye: cut each eye as separate top and bottom windows, drill the freckles with a small round bit, and save the eyebrows for last.
Beginner-friendlyRound and Square Eyes
A goofy lopsided face with one big round eye and one square eye, a small triangle nose, and a huge open smile interrupted by two buck teeth hanging from the upper lip. All shapes are cut fully through, and the mismatched eyes do all the comedic work. An easy, forgiving carve for kids and beginners; cut the smile last and leave the two tooth tabs of rind attached so they dangle into the glow.
Beginner-friendlyWide Grin and One Broad Tooth
Made for short, squat pumpkins, this goofy face pairs two upswept triangle eyes with an enormous grin interrupted by a single broad tooth hanging from the top lip. The eyes and mouth are cut through, and the tooth is simply a block of shell left in place inside the smile opening. Cut around the tooth carefully on both sides before removing the mouth pieces so it stays firmly attached.
AdvancedStar Crown and Four Tooth Grin
A crown of small four-point stars sparkles around the top of this face, while two big playful eyes with attached pupil tabs sit over a wide grin lined with little teeth. Everything is cut through, and the pupils survive as tabs rooted to the top of each eye opening. Carve the star crown first while the wall is strongest, then cut each eye around its pupil tab in small strokes so the tabs stay put.
AdvancedFour Teeth and Notched Tongue
Arched brows curve over squinting eyes while a huge open mouth shows four top teeth and a notched tongue lolling below, with short laugh lines radiating from each cheek. The face is all pierced cuts, and it rates hard because the tongue and teeth stay attached by narrow tabs inside the big mouth opening. Cut the mouth outline first, then carefully notch around the tongue tab last so it does not break free.
AdvancedUnequal Eyes and Tongue Grin
This mischievous face pairs one big round eye with a smaller sly one under arched brows, above a sprawling grin full of gapped teeth and a tongue-shaped opening lolling out below. Clusters of drilled dots frame each cheek like a glowing gridwork of freckles. It is all cut-through work with many narrow tooth bridges, so use a fine saw, cut the dots first, and support each bridge as you free the mouth pieces.