About this stencil
Download the Flamingo pumpkin stencil as a free printable PDF, then tape the pattern to your pumpkin and trace the lines. A flamingo stands with its long neck bent gracefully downward and its head dipped toward its breast on this easy Halloween pumpkin stencil. The entire bird is carved away as a single fluid silhouette revealing the glow within, while the two impossibly thin legs are the critical structural bridges connecting the large body void to the base of the cut. Score along each leg edge with a single controlled pass before removing the neighboring body mass on either side, so the legs don't fracture mid-cut. It works as a carving template for a Halloween jack-o'-lantern or a fall porch display. It is rated Beginner-friendly. Estimated time: 45-60 minutes. Actual time varies with preparation, pumpkin size and experience. Larger shapes and shorter cuts. An adult should handle sharp carving tools.
Pumpkin size guide
- 🎃 Small (5 to 7"): print at 80%
- 🎃 Medium (7 to 10"): print at 100% (recommended)
- 🎃 Large (11 to 13"): print at 130%
- 🎃 Giant (14"+): print at 150% on tabloid paper
Frequently asked questions
Can I resize this stencil?▾
Yes. The PDF is vector so it scales cleanly. Print the pattern at 100% for a 7 to 10 inch pumpkin, 130% for 11 to 13 inch, or 150% for a giant. Use your printer's "Fit to page" or "Custom scale" setting.
What kind of paper works best?▾
Standard 20 lb letter or A4 printer paper is fine. Heavier paper is harder to bend around the pumpkin curve. If your printer supports it, set the quality to 'best' so the lines are crisp.
How long will the carved pumpkin last?▾
Usually 5 to 10 days. Coat all cut surfaces with petroleum jelly and store the pumpkin somewhere cool overnight. Avoid direct sun. Battery LED pumpkin lights produce no heat and help it last longer.
Can I sell pumpkins carved with this stencil?▾
Yes, the carved pumpkin you make is yours. The license covers personal and small-scale commercial carving (selling carved pumpkins, photographing them, posting on social). You may not resell the PDF file itself.
What if my printer doesn't print the whole stencil?▾
Set 'Page scaling' to 'Fit' in the print dialog and uncheck 'Auto-rotate'. If it still cuts off, the design includes 0.25" of safe-area margin so a small crop won't ruin it.
How to carve this stencil
This is a cut-through stencil: the gray areas on the printable pattern are the pieces you remove, and everything white stays attached. The steps below give you the safest carving order. Plan on about 45-60 minutes from print to candle.
Set up first. Print the PDF at 100% scale on letter or A4 paper. Cut the lid at an angle, scoop the pumpkin clean, and thin the carving wall to about 1 inch where the design will sit. Tape the pattern on (snip small darts in the paper so it hugs the curve) and transfer every outline by poking dots along the lines, about one every 1/8 inch. Peel the paper away and carve dot to dot with short, straight strokes.
Carving order
- Cut the two thin legs first. Trace both long leg strips while the wall is fully rigid, including the small knee bulges and the webbed feet at the bottom. Use slow, single passes; these narrow channels are the most fragile part of the whole design.
- Free the drooping neck. Cut the S-curve of the neck from the body down to the rounded tip near the lower left. Work each side of the curve separately so the narrow bend does not tear.
- Release the body and head. Cut around the large head and back, finishing the small pointed feather tips at the rear and the tiny bill point under the head. Leave a short section along the back attached until last, support the plug with your free hand, and push it out from inside the pumpkin.
Clear loose fibers out of each opening as you go, and never twist or pry the blade against the shell; back it out and recut instead. When every piece is out, wipe the cut edges dry and drop in a battery LED puck.
Tools you'll need
For a beginner-friendly carve like this you'll want a paring knife, spoon / scoop, marker, and led pumpkin light. Here's the kit we reach for, but start with whatever you already own.
Elmchee Pumpkin Carving Kit
13-piece kit with carrying case
Saws for the larger cutouts, plus a scoop for hollowing. Covers both jobs in one kit.
View on Amazon ↗
HOME MOST LED Pumpkin Lights
4-pack, battery operated, with remote + timer
Orange glow made for jack-o'-lanterns. The remote and timer light the pumpkin every evening without reaching inside.
View on Amazon ↗
Speedball 4131 Lino Cutter Set
Handle + 5 interchangeable cutters
Interchangeable cutters for peeling and shading the face. Useful for the finer details.
View on Amazon ↗
Reviews from carvers
Every rating comes from a written review by someone who downloaded this stencil.
Carved this one?
Reviews are open to carvers who downloaded the stencil. Grab the free PDF, then come back and tell everyone how it went.
Community Pumpkin Carving Ideas
Carving ideas that use stencils like this one.
