Similar to This
View all stencils →About this stencil
A full lobster stretches sideways across the pumpkin with segmented tail, walking legs, long antennae, and two oversized claws rendered in shaved-skin relief. Nothing is pierced through: the body shapes are peeled bright while the segment lines and joints remain as dark etched divisions. This is a hard shading project because of all those segments, so map the outline first with shallow V-cuts, clear the large claw and tail areas, and save the skinny legs and antennae for careful final passes. This design is rated Advanced and takes most carvers around 150 minutes from trace to glow. Multi-layer cuts with skin-peel shading. Plan your cuts first.
Pumpkin size guide
- 🎃 Small (5–7") — print at 80%
- 🎃 Medium (7–10") — print at 100% (recommended)
- 🎃 Large (11–13") — print at 130%
- 🎃 Giant (14"+) — print at 150% on tabloid paper
Frequently asked questions
Can I resize this stencil?▾
Yes. The PDF is vector so it scales cleanly. Print at 100% for a 7–10 inch pumpkin, 130% for 11–13 inch, or 150% for a giant. Use your printer's "Fit to page" or "Custom scale" setting.
What kind of paper works best?▾
Standard 20 lb letter or A4 printer paper is fine. Heavier paper is harder to bend around the pumpkin curve. If your printer supports it, set the quality to 'best' so the lines are crisp.
How long will the carved pumpkin last?▾
Usually 5–10 days. Coat all cut surfaces with petroleum jelly and store the pumpkin somewhere cool overnight. Avoid direct sun. Battery LED pumpkin lights produce no heat and double the lifespan.
Can I sell pumpkins carved with this stencil?▾
Yes, the carved pumpkin you make is yours. The license covers personal and small-scale commercial carving (selling carved pumpkins, photographing them, posting on social). You may not resell the PDF file itself.
What if my printer doesn't print the whole stencil?▾
Set 'Page scaling' to 'Fit' in the print dialog and uncheck 'Auto-rotate'. If it still cuts off, the design includes 0.25" of safe-area margin so a small crop won't ruin it.
How to carve this stencil
- 1Print it
Download the PDF and print at 100% scale on letter or A4 paper.
- 2Prep the pumpkin
Cut the lid at an angle, scoop the guts, thin the wall to ~1 inch.
- 3Tape it on
Snip darts in the paper so it lies flat against the curve.
- 4Transfer the design
Poke along every line — about one dot every 1/8 inch.
- 5Carve it
Connect the dots with short straight cuts. Center first, work outward.
- 6Light it up
Drop in a battery LED pumpkin light and you're done.
Tools you'll need
For a advanced carve like this you'll want a linoleum cutter set, x-acto knife, peel tool, and pin transfer wheel. Here's the kit we reach for — start with whatever you already own.
Elmchee Pumpkin Carving Kit
13-piece kit with carrying case
Saws for the larger cutouts, plus a scoop for hollowing. Covers both jobs in one kit.
View on Amazon ↗
HOME MOST LED Pumpkin Lights
4-pack, battery operated, with remote + timer
Orange glow made for jack-o'-lanterns. The remote and timer light the pumpkin every evening without reaching inside.
View on Amazon ↗
Speedball 4131 Lino Cutter Set
Handle + 5 interchangeable cutters
Interchangeable cutters for peeling and shading the face. Useful for the finer details.
View on Amazon ↗
Community Pumpkin Carving Ideas
Carving ideas that use stencils like this one.
Related stencils
Carvers who liked this one also downloaded these.
Expert / ProTilted Jellyfish and Seaweed
A tilted jellyfish drifts with its domed bell up high and dozens of ribbony tentacles flowing down through strands of seaweed, while small bubbles rise around it. Every element is shaved into the skin at varying depths rather than cut through, creating layers of soft glow. This expert etch is all about depth control: shave the bell and bubbles deepest for brightness, keep the tentacles mid-depth, and leave the seaweed shallow so the jellyfish floats forward.
Expert / ProDomed Jellyfish and Bubbles
A ribbed jellyfish bell hovers near the top of the pumpkin, trailing eight long wavy tentacles that flow all the way to the base, with small bubbles rising on either side. The bell segments and tentacles are shaved to glowing flesh while thin strips of dark skin separate every ribbon, and the bubbles are pierced through. This expert shading design demands a steady hand; work each tentacle top to bottom in one continuous peel so the curves stay smooth and evenly lit.
IntermediateRunning Dinosaur and Long Tail
A velociraptor sprints across the pumpkin in full silhouette, head low, clawed legs mid-stride, and its long tail sweeping behind for balance. The entire dinosaur cuts through as one glowing shape, with the narrow tail and slim legs providing the medium challenge. Carve the thin tail and leg sections first in short segments, then remove the large body last so the delicate extremities are never left unsupported.
Beginner-friendlyHammerhead with Unequal Fins
A hammerhead shark cruising in full profile, its wide flattened head, tall dorsal fin, and forked tail all reading instantly in silhouette. The complete shark is one cut-through opening that stretches across the pumpkin's widest face for a dramatic glowing display. An easy carve with one caution: the slim notch between the tail forks is delicate, so cut it before removing the large body piece.
IntermediateThree Fish Above Two Waves
Three fish swim in a loose diagonal school above two rolling wave bands, with a trail of round bubbles rising toward the stem. Every element is cut through: fish bodies with notched tails, the long curved waves, and the bubble dots all become glowing openings. The waves are the longest cuts, so brace the pumpkin and saw them in smooth continuous strokes; poke the bubbles out first with a round tool while the wall is solid.
IntermediateCurled Dolphin Profile
A leaping dolphin caught mid-arc, its curved body, pointed snout, dorsal fin, and sweeping tail all glowing through one sculpted cut-through opening, with an intact rind island shaping the pectoral fin and belly. The interior island is the key feature: cut the outer outline in sections and leave the connecting bridges to the island untouched until the very end, then trim them carefully to final width.