Similar to This
View all stencils →About this stencil
A mischievous jack-o'-lantern with deliberately uneven eyes under slanted brows, a triangle nose, and a huge crooked grin interrupted by five hanging teeth. All the features are pierced clean through so candlelight pours out of every gap. The teeth are the trickiest part at this medium level, so cut around each one slowly and leave those tabs attached to the rim of the mouth. This design is rated Intermediate and takes most carvers around 75 minutes from trace to glow. Comfortable knife handling required. Small details and curves.
Pumpkin size guide
- 🎃 Small (5–7") — print at 80%
- 🎃 Medium (7–10") — print at 100% (recommended)
- 🎃 Large (11–13") — print at 130%
- 🎃 Giant (14"+) — print at 150% on tabloid paper
Frequently asked questions
Can I resize this stencil?▾
Yes. The PDF is vector so it scales cleanly. Print at 100% for a 7–10 inch pumpkin, 130% for 11–13 inch, or 150% for a giant. Use your printer's "Fit to page" or "Custom scale" setting.
What kind of paper works best?▾
Standard 20 lb letter or A4 printer paper is fine. Heavier paper is harder to bend around the pumpkin curve. If your printer supports it, set the quality to 'best' so the lines are crisp.
How long will the carved pumpkin last?▾
Usually 5–10 days. Coat all cut surfaces with petroleum jelly and store the pumpkin somewhere cool overnight. Avoid direct sun. Battery LED pumpkin lights produce no heat and double the lifespan.
Can I sell pumpkins carved with this stencil?▾
Yes, the carved pumpkin you make is yours. The license covers personal and small-scale commercial carving (selling carved pumpkins, photographing them, posting on social). You may not resell the PDF file itself.
What if my printer doesn't print the whole stencil?▾
Set 'Page scaling' to 'Fit' in the print dialog and uncheck 'Auto-rotate'. If it still cuts off, the design includes 0.25" of safe-area margin so a small crop won't ruin it.
How to carve this stencil
- 1Print it
Download the PDF and print at 100% scale on letter or A4 paper.
- 2Prep the pumpkin
Cut the lid at an angle, scoop the guts, thin the wall to ~1 inch.
- 3Tape it on
Snip darts in the paper so it lies flat against the curve.
- 4Transfer the design
Poke along every line — about one dot every 1/8 inch.
- 5Carve it
Connect the dots with short straight cuts. Center first, work outward.
- 6Light it up
Drop in a battery LED pumpkin light and you're done.
Tools you'll need
For a intermediate carve like this you'll want a x-acto knife, poker tool, ribbon scoop, and painter's tape. Here's the kit we reach for — start with whatever you already own.
Elmchee Pumpkin Carving Kit
13-piece kit with carrying case
Saws for the larger cutouts, plus a scoop for hollowing. Covers both jobs in one kit.
View on Amazon ↗
HOME MOST LED Pumpkin Lights
4-pack, battery operated, with remote + timer
Orange glow made for jack-o'-lanterns. The remote and timer light the pumpkin every evening without reaching inside.
View on Amazon ↗
Speedball 4131 Lino Cutter Set
Handle + 5 interchangeable cutters
Interchangeable cutters for peeling and shading the face. Useful for the finer details.
View on Amazon ↗
Community Pumpkin Carving Ideas
Carving ideas that use stencils like this one.
Related stencils
Carvers who liked this one also downloaded these.
Beginner-friendlyWide Grin with Three Teeth
One enormous sweeping grin and nothing else: a wide crescent mouth interrupted by two blocky upper teeth and a single lower tooth, with no eyes at all for a mysterious, cheeky effect. The whole smile is cut through, so it pours light across the porch. An easy carve that goes quickly; remove the mouth in left and right halves around the teeth so the tooth tabs never take any strain.
Beginner-friendlyTwo Lower Teeth Smile
This cheerful jack-o'-lantern face pairs two big round eyes with a wide open grin interrupted by a pair of goofy buck teeth. The eyes and mouth are cut all the way through, while the two square teeth are left attached to the top lip. Since it is an easy carve, just take care around those teeth: cut the mouth opening around them and leave each tooth anchored so it does not snap off.
IntermediateLopsided Zigzag Grin
A cheerfully lopsided jack-o'-lantern face with one big round eye, one slanted triangle eye, and a wide zigzag grin stretching across the pumpkin. All three features are pierced fully through so candlelight pours out, while the surrounding skin stays untouched. The zigzag mouth is the trickiest part at this medium level, so cut each tooth point in two short strokes that meet at the tip instead of dragging one long sawing pass.
Beginner-friendlyGoofy Three-Tooth Grin
A lovable goofy face with two big round eyes, a small triangle nose, and a wide smile broken up by three blocky teeth. Every shape is a full cut-through opening, so the eyes, nose, and mouth glow while the rest of the pumpkin stays untouched. It is a great first stencil; start with the smallest tooth cuts before opening the large mouth so the wall stays sturdy.
AdvancedSide-Glance and Stitched Grin
Two crescent-moon eyes glance slyly to the side above a small triangle nose and a mouth packed with a fence of narrow, uneven teeth. All openings cut through, and the row of skinny tooth gaps is what makes this a hard carve. Pierce and remove the little slots between teeth first, while the surrounding wall still supports them, then finish the big eye crescents and the mouth outline last.
IntermediateOne Eye and Two Upper Teeth
A goofy one-eyed jack-o'-lantern with a huge round eye topped by a dark pupil circle, a small triangle nose, and a wide smile broken by two chunky upper teeth. The big eye, nose, and mouth are cut through, while the pupil area keeps a disc of skin attached at the top for contrast. Support the teeth by cutting away from their narrow roots, since those two tabs carry the whole grin.