Similar to This
View all stencils →About this stencil
A friendly little ghost lifts one stubby arm in a wave, its four-lobed hem trailing below round eyes and a happy open mouth. The whole figure is shaved shading: you remove skin inside the body so it glows softly, then leave the eyes and mouth as raised uncarved pumpkin. Even, shallow shaving is all it takes, which makes this a forgiving introduction to etching. This design is rated Beginner-friendly and takes most carvers around 30 minutes from trace to glow. Great for kids and first-timers. Big shapes, short cuts.
Pumpkin size guide
- 🎃 Small (5–7") — print at 80%
- 🎃 Medium (7–10") — print at 100% (recommended)
- 🎃 Large (11–13") — print at 130%
- 🎃 Giant (14"+) — print at 150% on tabloid paper
Frequently asked questions
Can I resize this stencil?▾
Yes. The PDF is vector so it scales cleanly. Print at 100% for a 7–10 inch pumpkin, 130% for 11–13 inch, or 150% for a giant. Use your printer's "Fit to page" or "Custom scale" setting.
What kind of paper works best?▾
Standard 20 lb letter or A4 printer paper is fine. Heavier paper is harder to bend around the pumpkin curve. If your printer supports it, set the quality to 'best' so the lines are crisp.
How long will the carved pumpkin last?▾
Usually 5–10 days. Coat all cut surfaces with petroleum jelly and store the pumpkin somewhere cool overnight. Avoid direct sun. Battery LED pumpkin lights produce no heat and double the lifespan.
Can I sell pumpkins carved with this stencil?▾
Yes, the carved pumpkin you make is yours. The license covers personal and small-scale commercial carving (selling carved pumpkins, photographing them, posting on social). You may not resell the PDF file itself.
What if my printer doesn't print the whole stencil?▾
Set 'Page scaling' to 'Fit' in the print dialog and uncheck 'Auto-rotate'. If it still cuts off, the design includes 0.25" of safe-area margin so a small crop won't ruin it.
How to carve this stencil
- 1Print it
Download the PDF and print at 100% scale on letter or A4 paper.
- 2Prep the pumpkin
Cut the lid at an angle, scoop the guts, thin the wall to ~1 inch.
- 3Tape it on
Snip darts in the paper so it lies flat against the curve.
- 4Transfer the design
Poke along every line — about one dot every 1/8 inch.
- 5Carve it
Connect the dots with short straight cuts. Center first, work outward.
- 6Light it up
Drop in a battery LED pumpkin light and you're done.
Tools you'll need
For a beginner-friendly carve like this you'll want a paring knife, spoon / scoop, marker, and led pumpkin light. Here's the kit we reach for — start with whatever you already own.
Elmchee Pumpkin Carving Kit
13-piece kit with carrying case
Saws for the larger cutouts, plus a scoop for hollowing. Covers both jobs in one kit.
View on Amazon ↗
HOME MOST LED Pumpkin Lights
4-pack, battery operated, with remote + timer
Orange glow made for jack-o'-lanterns. The remote and timer light the pumpkin every evening without reaching inside.
View on Amazon ↗
Speedball 4131 Lino Cutter Set
Handle + 5 interchangeable cutters
Interchangeable cutters for peeling and shading the face. Useful for the finer details.
View on Amazon ↗
Community Pumpkin Carving Ideas
Carving ideas that use stencils like this one.
Related stencils
Carvers who liked this one also downloaded these.
Beginner-friendlyGhost with Three Uneven Points
A single billowy ghost with two raised arms and a wavy hem ending in three uneven points, carved as one big glowing cutout. The entire ghost silhouette is pierced through, so candlelight fills the friendly specter from arms to tail. This easy one-piece design suits squat pumpkins with plenty of front surface; cut the smooth outer curves first and finish with the scalloped bottom points, which are the only fiddly bits.
AdvancedCurled-Hand Ghost & Round Glow
A wide-eyed little ghost with curled hands and a wavy hem floats in front of a big round glow, its startled O-shaped mouth mid-boo. The circular background is cut through around the ghost, so the figure stays as connected rind while light floods the disc behind it. Those slim connector bridges at the hands and hem are the whole design; cut the large background sections first and save every bridge for careful final passes.
IntermediateWaving Wispy Ghost
A friendly ghost with trailing wisps waves from the pumpkin, its oval eyes and mouth left as darker raised skin against the pale shaved body. There are no pierced openings; you peel the skin away inside the ghost outline so the flesh glows gently when lit. Shave in smooth, overlapping strokes and stop at the eye and mouth outlines so those features stay dark and crisp.
Expert / ProMoonlit Seal and Water Bands
A harbor seal rests on the shore with its head raised and tail curled up, backed by a huge full moon, drifting clouds, and bands of rippling water below. The entire scene is skin-shaved shading with no pierced holes, so the moon glows brightest behind the seal's darker sculpted body. Expert carvers should establish the moon's deep, even shave first, then build the seal with shallower graded layers so its whiskered face keeps crisp contrast.
Beginner-friendlySeated Dog with Bone and Dots
A patient pup sits in profile, ears perked and tail resting, while a bone floats nearby with a trail of small dream-bubble dots connecting them. The dog's body, the bone, and the dots are all cut fully through as bold, separate openings, so the scene reads instantly from the street. This easy design has no fragile interior bridges; just cut the large dog body in two or three sections and pop the bone and dots out last for a tidy finish.
IntermediateHeart Cheeks and Eight Dots
An irresistibly cute kawaii face: two tall oval eyes, a tiny curved smile, a heart-shaped blush on each cheek, and eight little sparkle dots scattered around the edges. Every element is a small pierced opening, and the wide spacing across a squat pumpkin gives it that classic sticker-art charm. At medium difficulty the hearts and dots demand patience; use a drill bit or apple corer for the round sparkles to keep them perfectly circular.