Similar to This
View all stencils →About this stencil
A gymnast frozen mid split leap, legs stretched into a full horizontal line with arms swept back and hair in a neat bun. The entire figure is cut through as one connected opening, so she glows like a spotlight silhouette on the pumpkin. Rated hard because the legs taper to slim points at the toes; carve from the torso outward and finish the narrow limb tips last with light, shallow strokes. This design is rated Advanced and takes most carvers around 150 minutes from trace to glow. Multi-layer cuts with skin-peel shading. Plan your cuts first.
Pumpkin size guide
- 🎃 Small (5–7") — print at 80%
- 🎃 Medium (7–10") — print at 100% (recommended)
- 🎃 Large (11–13") — print at 130%
- 🎃 Giant (14"+) — print at 150% on tabloid paper
Frequently asked questions
Can I resize this stencil?▾
Yes. The PDF is vector so it scales cleanly. Print at 100% for a 7–10 inch pumpkin, 130% for 11–13 inch, or 150% for a giant. Use your printer's "Fit to page" or "Custom scale" setting.
What kind of paper works best?▾
Standard 20 lb letter or A4 printer paper is fine. Heavier paper is harder to bend around the pumpkin curve. If your printer supports it, set the quality to 'best' so the lines are crisp.
How long will the carved pumpkin last?▾
Usually 5–10 days. Coat all cut surfaces with petroleum jelly and store the pumpkin somewhere cool overnight. Avoid direct sun. Battery LED pumpkin lights produce no heat and double the lifespan.
Can I sell pumpkins carved with this stencil?▾
Yes, the carved pumpkin you make is yours. The license covers personal and small-scale commercial carving (selling carved pumpkins, photographing them, posting on social). You may not resell the PDF file itself.
What if my printer doesn't print the whole stencil?▾
Set 'Page scaling' to 'Fit' in the print dialog and uncheck 'Auto-rotate'. If it still cuts off, the design includes 0.25" of safe-area margin so a small crop won't ruin it.
How to carve this stencil
- 1Print it
Download the PDF and print at 100% scale on letter or A4 paper.
- 2Prep the pumpkin
Cut the lid at an angle, scoop the guts, thin the wall to ~1 inch.
- 3Tape it on
Snip darts in the paper so it lies flat against the curve.
- 4Transfer the design
Poke along every line — about one dot every 1/8 inch.
- 5Carve it
Connect the dots with short straight cuts. Center first, work outward.
- 6Light it up
Drop in a battery LED pumpkin light and you're done.
Tools you'll need
For a advanced carve like this you'll want a linoleum cutter set, x-acto knife, peel tool, and pin transfer wheel. Here's the kit we reach for — start with whatever you already own.
Elmchee Pumpkin Carving Kit
13-piece kit with carrying case
Saws for the larger cutouts, plus a scoop for hollowing. Covers both jobs in one kit.
View on Amazon ↗
HOME MOST LED Pumpkin Lights
4-pack, battery operated, with remote + timer
Orange glow made for jack-o'-lanterns. The remote and timer light the pumpkin every evening without reaching inside.
View on Amazon ↗
Speedball 4131 Lino Cutter Set
Handle + 5 interchangeable cutters
Interchangeable cutters for peeling and shading the face. Useful for the finer details.
View on Amazon ↗
Community Pumpkin Carving Ideas
Carving ideas that use stencils like this one.
Related stencils
Carvers who liked this one also downloaded these.
AdvancedLeaping Gymnast with Stars
A gymnast soars in a full split leap, one arm reaching skyward toward a trail of stars and a curved comet streak behind her. The whole figure is a shaded carve on a continuous wall, shaving the skin so the silhouette glows without any pierced holes, which preserves the slender arms and pointed toes. Shave the thin limbs in light passes with a small loop tool, since going too deep on those narrow lines risks breaking through.
AdvancedTree Pose with Raised Arms
A serene figure balances in yoga tree pose, arms raised overhead and one foot tucked against the standing leg, flanked by leafy sprigs on a shaved ground line. The design is entirely skin-shave shading with no pierced holes, so the figure glows in pale relief against the dark rind. Shave the torso and legs in long continuous strokes for smooth lines, then detail the thin arms and leaves with a fine gouge.
Expert / ProBaseball and Crossed Bats
A trophy-worthy relief of a baseball resting over two crossed bats, all standing out from a recessed panel in true sculpted depth. The ball's curved stitch lines and the bats' grain and knobs are incised details, and nothing pierces the wall. Excavate the background panel to an even depth before rounding the ball, and undercut the bat edges slightly so they cast real shadows in daylight.
Beginner-friendlyPlain Fire Helmet Silhouette
A traditional firefighter helmet in bold silhouette, showing the raised front shield, domed crown, and long swooping rear brim that flares out to protect the neck. The entire helmet is cut through as one large opening, so it glows as a single unmistakable emblem. This easy tribute carve works great on a big pumpkin; cut the long brim curve in one slow continuous pass to keep its sweep smooth.
IntermediateNine Triangles and Six Dots
Nine triangles in alternating sizes form a tidy three-by-three grid, with six small round dots tucked into the gaps between rows. Each triangle and dot is cut straight through, producing a clean modern lantern that glows like patterned tilework. This medium design is all about alignment, so tape the template securely, transfer every corner point before cutting, and carve the triangles row by row to keep the grid looking sharp and even.
IntermediateSix Waves Sun and Starfish
A half-sun sets over two rows of curling surf, six stylized waves in all, with a chunky starfish tucked at the end of the bottom row. Each wave curl, the sun, and the starfish are individual cut-through openings separated by healthy strips of skin. For a medium carve like this, work top row first and keep the skin bridges between waves at least finger-width so the pattern stays strong through the whole session.