Similar to This
View all stencils →About this stencil
The classic thumbs-up hand, thumb raised high over four curled fingers, presented as a bold etched panel on the pumpkin's face. No holes are pierced; you shave the outer skin inside the hand outline so the pale flesh forms the gesture, leaving thin rind lines to separate the fingers. Keep the shaved depth even and stop at each finger line so the knuckle ridges stay dark and readable. This design is rated Intermediate and takes most carvers around 75 minutes from trace to glow. Comfortable knife handling required. Small details and curves.
Pumpkin size guide
- 🎃 Small (5–7") — print at 80%
- 🎃 Medium (7–10") — print at 100% (recommended)
- 🎃 Large (11–13") — print at 130%
- 🎃 Giant (14"+) — print at 150% on tabloid paper
Frequently asked questions
Can I resize this stencil?▾
Yes. The PDF is vector so it scales cleanly. Print at 100% for a 7–10 inch pumpkin, 130% for 11–13 inch, or 150% for a giant. Use your printer's "Fit to page" or "Custom scale" setting.
What kind of paper works best?▾
Standard 20 lb letter or A4 printer paper is fine. Heavier paper is harder to bend around the pumpkin curve. If your printer supports it, set the quality to 'best' so the lines are crisp.
How long will the carved pumpkin last?▾
Usually 5–10 days. Coat all cut surfaces with petroleum jelly and store the pumpkin somewhere cool overnight. Avoid direct sun. Battery LED pumpkin lights produce no heat and double the lifespan.
Can I sell pumpkins carved with this stencil?▾
Yes, the carved pumpkin you make is yours. The license covers personal and small-scale commercial carving (selling carved pumpkins, photographing them, posting on social). You may not resell the PDF file itself.
What if my printer doesn't print the whole stencil?▾
Set 'Page scaling' to 'Fit' in the print dialog and uncheck 'Auto-rotate'. If it still cuts off, the design includes 0.25" of safe-area margin so a small crop won't ruin it.
How to carve this stencil
- 1Print it
Download the PDF and print at 100% scale on letter or A4 paper.
- 2Prep the pumpkin
Cut the lid at an angle, scoop the guts, thin the wall to ~1 inch.
- 3Tape it on
Snip darts in the paper so it lies flat against the curve.
- 4Transfer the design
Poke along every line — about one dot every 1/8 inch.
- 5Carve it
Connect the dots with short straight cuts. Center first, work outward.
- 6Light it up
Drop in a battery LED pumpkin light and you're done.
Tools you'll need
For a intermediate carve like this you'll want a x-acto knife, poker tool, ribbon scoop, and painter's tape. Here's the kit we reach for — start with whatever you already own.
Elmchee Pumpkin Carving Kit
13-piece kit with carrying case
Saws for the larger cutouts, plus a scoop for hollowing. Covers both jobs in one kit.
View on Amazon ↗
HOME MOST LED Pumpkin Lights
4-pack, battery operated, with remote + timer
Orange glow made for jack-o'-lanterns. The remote and timer light the pumpkin every evening without reaching inside.
View on Amazon ↗
Speedball 4131 Lino Cutter Set
Handle + 5 interchangeable cutters
Interchangeable cutters for peeling and shading the face. Useful for the finer details.
View on Amazon ↗
Community Pumpkin Carving Ideas
Carving ideas that use stencils like this one.
Related stencils
Carvers who liked this one also downloaded these.
Expert / ProThumbs Up with a Burst
A giant thumbs-up hand bursting from a starburst of radiating lines, complete with a rolled sleeve cuff, four curled fingers, and a proudly raised thumb. The whole emblem is continuous-wall relief carving, sculpted in layered depths with no cut-through openings, so the hand looks almost three-dimensional. This expert design depends on smooth rounded knuckles: rough out the fist as one mass, then separate the fingers with deep V-grooves before final smoothing.
AdvancedThumbs Up with Six Rays
A big thumbs-up hand surrounded by six radiating burst lines, like a glowing seal of approval for every trick-or-treater. The hand itself is sculpted in relief with shaved shading across the knuckles and thumb, while the outline gap and ray lines are carved deeper so light halos the whole gesture. Rough in the hand shape shallow at first, then deepen the shadows between the fingers gradually to keep the knuckles reading clearly.
Beginner-friendlyFour-Tongue Flame
One big flame fills the face of the pumpkin, its four licking tongues tapering to sharp points just like the classic fire symbol. The entire flame is a single cut-through shape, so candlelight literally becomes the fire. This is an easy carve with only one piece to remove; poke the pattern deeply at each flame tip first, then saw from the rounded base upward so the narrow points come out clean instead of ragged.
AdvancedTilted Laugh with Two Tears
This tilted laughing face leans hard to one side, with two squinted arrow eyes, a huge open grin, and a teardrop of joy flying off each corner. All the features cut fully through, and the diagonal tilt is what makes it read as the crying-laughing emoji everyone knows. It rates hard because the squint lines and tear droplets are small, so use a fine saw and drill-start each tiny opening before cutting.
Beginner-friendlyWeary Face Emoji Pumpkin Stencil
The weary face emoji is recreated here as a jack-o-lantern pumpkin stencil: a large circular face outline holds two sets of drooping curved eyebrow-and-eyelid pairs that express exhaustion, a wide open mouth with squared-off upper teeth, and a small chin sweat drop below. All the interior shapes are cut through as separate pieces nested inside the face circle. Carve the tiny sweat drop below the chin first since it is isolated and easy to lose track of, then work upward through the teeth, mouth, and finally the eye arcs.
Beginner-friendlySurprised Emoji Pumpkin Stencil
The surprised face emoji is translated into a pumpkin stencil with wide round eyes, a furrowed brow, a small nose bump, and a large open oval mouth. The face disc is partially cut away around the perimeter leaving a crescent of solid pumpkin at the top and right side; the eyes are rings with solid centers, and the mouth is a solid oval pierce. When lit, the face glows with an expression of shock. Carve the ring-shaped eye borders carefully: cut the outer circle first, then the inner pupil circle, leaving the solid dot of pumpkin wall between them untouched to preserve the iris-ring detail.