Similar to This
View all stencils →About this stencil
A spotted eagle ray glides diagonally across the pumpkin, its wide wings dotted with rows of round spots, a long whip tail trailing off behind, and a curled loop near the tail base. The whole creature is rendered by etching the skin: outlines and spots are shaved to glow softly while the wall stays sealed. Rated hard for the fine linework; carve the spots with a small round gouge and keep your outline strokes shallow and consistent. This design is rated Advanced and takes most carvers around 150 minutes from trace to glow. Multi-layer cuts with skin-peel shading. Plan your cuts first.
Pumpkin size guide
- 🎃 Small (5–7") — print at 80%
- 🎃 Medium (7–10") — print at 100% (recommended)
- 🎃 Large (11–13") — print at 130%
- 🎃 Giant (14"+) — print at 150% on tabloid paper
Frequently asked questions
Can I resize this stencil?▾
Yes. The PDF is vector so it scales cleanly. Print at 100% for a 7–10 inch pumpkin, 130% for 11–13 inch, or 150% for a giant. Use your printer's "Fit to page" or "Custom scale" setting.
What kind of paper works best?▾
Standard 20 lb letter or A4 printer paper is fine. Heavier paper is harder to bend around the pumpkin curve. If your printer supports it, set the quality to 'best' so the lines are crisp.
How long will the carved pumpkin last?▾
Usually 5–10 days. Coat all cut surfaces with petroleum jelly and store the pumpkin somewhere cool overnight. Avoid direct sun. Battery LED pumpkin lights produce no heat and double the lifespan.
Can I sell pumpkins carved with this stencil?▾
Yes, the carved pumpkin you make is yours. The license covers personal and small-scale commercial carving (selling carved pumpkins, photographing them, posting on social). You may not resell the PDF file itself.
What if my printer doesn't print the whole stencil?▾
Set 'Page scaling' to 'Fit' in the print dialog and uncheck 'Auto-rotate'. If it still cuts off, the design includes 0.25" of safe-area margin so a small crop won't ruin it.
How to carve this stencil
- 1Print it
Download the PDF and print at 100% scale on letter or A4 paper.
- 2Prep the pumpkin
Cut the lid at an angle, scoop the guts, thin the wall to ~1 inch.
- 3Tape it on
Snip darts in the paper so it lies flat against the curve.
- 4Transfer the design
Poke along every line — about one dot every 1/8 inch.
- 5Carve it
Connect the dots with short straight cuts. Center first, work outward.
- 6Light it up
Drop in a battery LED pumpkin light and you're done.
Tools you'll need
For a advanced carve like this you'll want a linoleum cutter set, x-acto knife, peel tool, and pin transfer wheel. Here's the kit we reach for — start with whatever you already own.
Elmchee Pumpkin Carving Kit
13-piece kit with carrying case
Saws for the larger cutouts, plus a scoop for hollowing. Covers both jobs in one kit.
View on Amazon ↗
HOME MOST LED Pumpkin Lights
4-pack, battery operated, with remote + timer
Orange glow made for jack-o'-lanterns. The remote and timer light the pumpkin every evening without reaching inside.
View on Amazon ↗
Speedball 4131 Lino Cutter Set
Handle + 5 interchangeable cutters
Interchangeable cutters for peeling and shading the face. Useful for the finer details.
View on Amazon ↗
Community Pumpkin Carving Ideas
Carving ideas that use stencils like this one.
Related stencils
Carvers who liked this one also downloaded these.
IntermediateFan Tail Fish with Low Notches
A plump fantail goldfish glides across the pumpkin as one big glowing silhouette, with a rounded body, sweeping double tail, and small notched fins along the belly. The entire fish is pierced through in a single connected shape, so it lights up like an aquarium at night. At medium difficulty the low fin notches are the detail work; cut the broad body and tail first, then nick out the small fin points with short careful strokes.
Beginner-friendlyHammerhead with Unequal Fins
A hammerhead shark cruising in full profile, its wide flattened head, tall dorsal fin, and forked tail all reading instantly in silhouette. The complete shark is one cut-through opening that stretches across the pumpkin's widest face for a dramatic glowing display. An easy carve with one caution: the slim notch between the tail forks is delicate, so cut it before removing the large body piece.
IntermediateThree Fish Above Two Waves
Three fish swim in a loose diagonal school above two rolling wave bands, with a trail of round bubbles rising toward the stem. Every element is cut through: fish bodies with notched tails, the long curved waves, and the bubble dots all become glowing openings. The waves are the longest cuts, so brace the pumpkin and saw them in smooth continuous strokes; poke the bubbles out first with a round tool while the wall is solid.
IntermediateCurled Dolphin Profile
A leaping dolphin caught mid-arc, its curved body, pointed snout, dorsal fin, and sweeping tail all glowing through one sculpted cut-through opening, with an intact rind island shaping the pectoral fin and belly. The interior island is the key feature: cut the outer outline in sections and leave the connecting bridges to the island untouched until the very end, then trim them carefully to final width.
IntermediateGecko with Thirteen Toe Tips
A gecko sprawls diagonally across the pumpkin as one bold silhouette, splayed toes gripping and its thick tail curving away. The entire lizard is a single cut-through aperture, so the whole body glows as one connected shape with those distinctive rounded toe pads catching the light. At medium difficulty, the toes are the trick: cut each tiny pad by connecting it to its leg with a short channel, and remove the big body piece last.
Beginner-friendlyRound Fish and Three Bubbles
A plump fish silhouette with a notched triangle tail swims across the pumpkin, trailed by three round bubbles rising toward the stem. The fish body and each bubble cut completely through, giving anglers a bold, glowing catch with almost no fine detail to fuss over. An easy pattern; remove the large body in two pieces split at the tail notch, then drill or carve the bubbles smallest to largest.