🎃

🎃32 designs · Updated for 2026

Family Jack O Lantern Pumpkin Designs

Looking for family jack o lantern pumpkin designs? You're in the right place. Print at 100% scale, tape it to your pumpkin, and poke through the lines with a pin.

Browse 32 designs ↓

★★★★★4.9/5from 2,400+ carvers✓ No watermark✓ Print-ready PDF

🆓

100% free

Every design is a free download. No account, no catch.

⚡

Print-ready PDF

One click to a clean PDF, pre-sized for a standard 8.5×11 sheet.

✂️

Carve tonight

Print, tape it to your pumpkin, trace the lines, and start carving.

32 family jack o lantern pumpkin designs

Pick a favorite, hit print, and you'll have a glowing porch by sundown.

Intermediate

Sleepy Eyes and Eight Lashes

Two closed crescent eyes with four little lashes apiece rest above a small oval mouth, while round dots on each side form rosy cheeks for a sweetly sleeping face. Every crescent, lash, dot, and the mouth is pierced through, so the tiny lash cuts do the expressive work. Cut the two big crescents first, then add the short lash strokes with a fine saw, keeping each one clear of its neighbor.

Free PDF

Intermediate

Wink and Five Rounded Gaps

One eye is a jaunty upswept crescent wink while the other stays a wide triangle, set over a small diamond nose and a lopsided grin broken into five rounded gaps by chunky teeth. The eyes, nose, and mouth gaps are cut through, leaving the tooth shapes as attached skin between them. A medium carver should cut the five mouth gaps individually rather than one big mouth, which keeps every tooth solidly connected and the crooked smile intact.

Free PDF

Intermediate

Unequal Eyes and Six Slashes

A menacing sneer built from two uneven glaring eyes, a small skull-like nose, a crooked mouth of jagged teeth, and three claw-slash marks raking each side of the face. All shapes pierce through, and the mismatched features do the intimidating. A medium carve; cut the six narrow slashes first with single confident strokes, then work the mouth teeth before opening the larger eye shapes.

Free PDF

Intermediate

Winking Seven-Tooth Grin

A goofy winking jack-o'-lantern with one wide round eye, one squinting wink, a triangle nose, and an enormous grin broken up by a jumble of square and pointed teeth along both lips. Every feature is cut clean through so the mismatched expression beams from the whole face. At medium difficulty the mouth is the main event; cut the grin outline first, then shape each tooth individually, alternating sides so the lip strips stay supported.

Free PDF

Intermediate

Wink and Barred Square Grin

One huge round eye stares while the other squeezes into a curled wink above a giant open grin packed with blocky square teeth, and freckle dots sprinkle each cheek. The eyes, mouth, and freckles all cut through the wall, with skin bridges left in place to form the teeth. Cut the mouth's outer outline first, then remove the gaps between teeth one at a time so each block stays anchored.

Free PDF

Intermediate

Angry Eyes and Five Mouth Gaps

A grumpy jack-o'-lantern scowls with slanted, brow-slit eyes, a small triangle nose, angled cheek slashes, and a downturned mouth broken into square gaps. Every element is cut through, with the mouth's rind bridges creating the clenched, gritted-teeth effect. The thin brow and cheek slits earn the medium rating: make each slit with two close parallel cuts and pop the sliver out from inside the pumpkin, since pushing from outside can crack the narrow channel wider.

Free PDF

Intermediate

Oval Eyes and Crescent Cheeks

This delighted face beams with two big oval eyes, a small triangle nose, crescent-shaped cheek accents, and an open grin showing a pair of stubby teeth, all dusted with tiny freckle holes. Every shape is pierced through, with the teeth left attached to the upper lip. Cut the delicate crescent cheeks with the tip of your saw only, since their thin curves are the easiest pieces to crack.

Free PDF

Intermediate

Triangle Eyes and Six Diamonds

This elevated take on the traditional face pairs slanted triangle eyes topped with thin brow slits, a triangle nose, and a deep zigzag grin, then adds three small diamond cutouts on each cheek for extra sparkle. Every element is pierced through the wall. The brow slits and little diamonds are what push it to medium; cut the big shapes first, then handle each diamond with a narrow saw, working point to point so they stay crisp.

Free PDF

Intermediate

Oval Eyes and Eight Cheek Dots

Big oval eyes sit under arched brows above a round button nose and a broad smile showing four blunt square teeth, with four freckle dots sprinkled on each cheek. The eyes, brows, nose, mouth, and dots are pierced through while the tooth bridges stay connected. Poke the eight small cheek dots first, then cut the large features, leaving the tooth bars until the end so they keep support.

Free PDF

Intermediate

Unequal Eyes and Crooked Teeth

This lovably lopsided face pairs one round eye with one droopy crescent eye, a triangle nose, and a huge crooked grin full of uneven square teeth, plus a pair of dot dimples on each cheek. The eyes, nose, mouth, and dots are pierced while the mismatched tooth bars stay attached. It suits odd-shaped pumpkins perfectly; cut the tooth gaps in random sizes and the wonkier it looks, the better.

Free PDF

Intermediate

Almond Eyes and Seven Teeth

A wide, low jack-o'-lantern face with sly almond-shaped eyes, a small triangle nose, and a long jagged mouth packed with alternating square teeth top and bottom. Everything is pierced through, and the horizontal layout suits squat, wide pumpkins. At medium difficulty the tooth row is the main work; cut the mouth's outer outline first, then remove the gaps between teeth one at a time so each block keeps support while you work.

Free PDF

Intermediate

Left Wink and Six Cheek Wedges

A playful winking jack-o'-lantern: one big round open eye, one arched wink, a triangle nose, and a smiling mouth with blocky teeth, all framed by three thin whisker-like wedges slashed across each cheek. Every opening is cut through, and the six cheek wedges throw extra slivers of light. At medium difficulty, cut the large features first and finish with the skinny cheek slits, using a fine saw so each wedge tapers to a clean point.

Free PDF