Similar to This
View all stencils →About this stencil
A velociraptor sprints across the pumpkin in full silhouette, head low, clawed legs mid-stride, and its long tail sweeping behind for balance. The entire dinosaur cuts through as one glowing shape, with the narrow tail and slim legs providing the medium challenge. Carve the thin tail and leg sections first in short segments, then remove the large body last so the delicate extremities are never left unsupported. This design is rated Intermediate and takes most carvers around 75 minutes from trace to glow. Comfortable knife handling required. Small details and curves.
Pumpkin size guide
- 🎃 Small (5–7") — print at 80%
- 🎃 Medium (7–10") — print at 100% (recommended)
- 🎃 Large (11–13") — print at 130%
- 🎃 Giant (14"+) — print at 150% on tabloid paper
Frequently asked questions
Can I resize this stencil?▾
Yes. The PDF is vector so it scales cleanly. Print at 100% for a 7–10 inch pumpkin, 130% for 11–13 inch, or 150% for a giant. Use your printer's "Fit to page" or "Custom scale" setting.
What kind of paper works best?▾
Standard 20 lb letter or A4 printer paper is fine. Heavier paper is harder to bend around the pumpkin curve. If your printer supports it, set the quality to 'best' so the lines are crisp.
How long will the carved pumpkin last?▾
Usually 5–10 days. Coat all cut surfaces with petroleum jelly and store the pumpkin somewhere cool overnight. Avoid direct sun. Battery LED pumpkin lights produce no heat and double the lifespan.
Can I sell pumpkins carved with this stencil?▾
Yes, the carved pumpkin you make is yours. The license covers personal and small-scale commercial carving (selling carved pumpkins, photographing them, posting on social). You may not resell the PDF file itself.
What if my printer doesn't print the whole stencil?▾
Set 'Page scaling' to 'Fit' in the print dialog and uncheck 'Auto-rotate'. If it still cuts off, the design includes 0.25" of safe-area margin so a small crop won't ruin it.
How to carve this stencil
This is a cut-through stencil: the dark numbered regions on the printable pattern are the pieces you remove, and everything white stays attached. The numbers give you the safest carving order, and the steps below walk through them one by one. Plan on about 50-75 minutes from print to candle.
Set up first. Print the PDF at 100% scale on letter or A4 paper. Cut the lid at an angle, scoop the pumpkin clean, and thin the carving wall to about 1 inch where the design will sit. Tape the pattern on (snip small darts in the paper so it hugs the curve) and transfer every outline by poking dots along the lines, about one every 1/8 inch. Peel the paper away and carve dot to dot with short, straight strokes.
Carving order
- Cut the long-tailed runner. Cut region 1 around the rounded right head, long sweeping left tail, small curled arm and two uneven running feet. Preserve the open white thigh curve and leg gaps. Keep the head plain and support the narrow feet while releasing the plug.
Clear loose fibers out of each opening as you go, and never twist or pry the blade against the shell; back it out and recut instead. When every region is open, wipe the cut edges dry and drop in a battery LED puck.
Tools you'll need
For a intermediate carve like this you'll want a x-acto knife, poker tool, ribbon scoop, and painter's tape. Here's the kit we reach for — start with whatever you already own.
Elmchee Pumpkin Carving Kit
13-piece kit with carrying case
Saws for the larger cutouts, plus a scoop for hollowing. Covers both jobs in one kit.
View on Amazon ↗
HOME MOST LED Pumpkin Lights
4-pack, battery operated, with remote + timer
Orange glow made for jack-o'-lanterns. The remote and timer light the pumpkin every evening without reaching inside.
View on Amazon ↗
Speedball 4131 Lino Cutter Set
Handle + 5 interchangeable cutters
Interchangeable cutters for peeling and shading the face. Useful for the finer details.
View on Amazon ↗
Community Pumpkin Carving Ideas
Carving ideas that use stencils like this one.
Related stencils
Carvers who liked this one also downloaded these.
IntermediateOpen-Jawed T-Rex
An open-jawed T-Rex strides across the pumpkin in full profile, tiny arms forward and thick tail sweeping behind. The entire dinosaur is a shaded silhouette: shave away the skin inside the body so the shape shows as a lighter panel against the orange rind, with no pierced holes. At medium difficulty, outline the jaws, claws, and tail tip carefully first, since those narrow points define the whole silhouette when the sun or candle hits it.
IntermediatePterodactyl & Unequal Wings
A soaring pterodactyl caught mid-flight, with one wing swept high and the other stretched wide, a long crested head, open beak, and trailing legs. The whole silhouette is shaded by shaving away the skin, so the pale flying reptile appears against the darker pumpkin without any pierced holes. At medium difficulty the key is the wing edges: score the outline first with a light pass, then scrape inward so the membrane shapes stay crisp.
Beginner-friendlyStriding Velociraptor Pumpkin Stencil
A velociraptor in full stride dominates this easy pumpkin stencil, shown in profile with its distinctive upright neck, narrow head, small forelimbs, and long stiffened tail extended behind it. The entire dinosaur silhouette is cut as a single open shape, and a small inner detail near the chest is removed separately to show the bent arm. Lit from behind, it reads instantly as a raptor shadow against the glowing pumpkin. Trace the tail outline before cutting because the long thin tail tip can run outside the pumpkin's curve if not centered.
AdvancedVelociraptor Pumpkin Stencil
A snarling velociraptor lunges forward on this dinosaur pumpkin stencil, its open jaws showing individual teeth, forelegs raised with curved claws, and a long stiff tail arcing behind. The design uses a mix of pierced negative space and thin pumpkin-wall bridges to define the body segments, so the lit jack-o-lantern shows the raptor as an orange figure ringed by dark gaps. Start by cutting the smallest interior tooth shapes and claw details before removing the large body sections, so the surrounding wall keeps the stencil stable throughout.
Expert / ProTilted Jellyfish and Seaweed
A tilted jellyfish drifts with its domed bell up high and dozens of ribbony tentacles flowing down through strands of seaweed, while small bubbles rise around it. Every element is shaved into the skin at varying depths rather than cut through, creating layers of soft glow. This expert etch is all about depth control: shave the bell and bubbles deepest for brightness, keep the tentacles mid-depth, and leave the seaweed shallow so the jellyfish floats forward.
Expert / ProDomed Jellyfish and Bubbles
A ribbed jellyfish bell hovers near the top of the pumpkin, trailing eight long wavy tentacles that flow all the way to the base, with small bubbles rising on either side. The bell segments and tentacles are shaved to glowing flesh while thin strips of dark skin separate every ribbon, and the bubbles are pierced through. This expert shading design demands a steady hand; work each tentacle top to bottom in one continuous peel so the curves stay smooth and evenly lit.