Similar to This
View all stencils →About this stencil
A bird bursts forward with both wings spread wide, every flight feather notched along the wing edges, above a fanned notched tail. The whole spread-wing shape is one dramatic cut-through, so the bird blazes as a single figure of light. Rated medium because of the many feather notches along the wingtips; cut the main body opening first, then nibble out each feather notch with short strokes so the points stay defined. This design is rated Intermediate and takes most carvers around 75 minutes from trace to glow. Comfortable knife handling required. Small details and curves.
Pumpkin size guide
- 🎃 Small (5–7") — print at 80%
- 🎃 Medium (7–10") — print at 100% (recommended)
- 🎃 Large (11–13") — print at 130%
- 🎃 Giant (14"+) — print at 150% on tabloid paper
Frequently asked questions
Can I resize this stencil?▾
Yes. The PDF is vector so it scales cleanly. Print at 100% for a 7–10 inch pumpkin, 130% for 11–13 inch, or 150% for a giant. Use your printer's "Fit to page" or "Custom scale" setting.
What kind of paper works best?▾
Standard 20 lb letter or A4 printer paper is fine. Heavier paper is harder to bend around the pumpkin curve. If your printer supports it, set the quality to 'best' so the lines are crisp.
How long will the carved pumpkin last?▾
Usually 5–10 days. Coat all cut surfaces with petroleum jelly and store the pumpkin somewhere cool overnight. Avoid direct sun. Battery LED pumpkin lights produce no heat and double the lifespan.
Can I sell pumpkins carved with this stencil?▾
Yes, the carved pumpkin you make is yours. The license covers personal and small-scale commercial carving (selling carved pumpkins, photographing them, posting on social). You may not resell the PDF file itself.
What if my printer doesn't print the whole stencil?▾
Set 'Page scaling' to 'Fit' in the print dialog and uncheck 'Auto-rotate'. If it still cuts off, the design includes 0.25" of safe-area margin so a small crop won't ruin it.
How to carve this stencil
This is a cut-through stencil: the dark numbered regions on the printable pattern are the pieces you remove, and everything white stays attached. The numbers give you the safest carving order, and the steps below walk through them one by one. Plan on about 45-70 minutes from print to candle.
Set up first. Print the PDF at 100% scale on letter or A4 paper. Cut the lid at an angle, scoop the pumpkin clean, and thin the carving wall to about 1 inch where the design will sit. Tape the pattern on (snip small darts in the paper so it hugs the curve) and transfer every outline by poking dots along the lines, about one every 1/8 inch. Peel the paper away and carve dot to dot with short, straight strokes.
Carving order
- Trace both wings and the tail. Cut region 1 around the two unequal lifted wings, small square-topped head and broad lower tail. Follow the stepped feather edges. Preserve both long white notches beside the tail and support the wide plug while finishing the outer wing tips.
Clear loose fibers out of each opening as you go, and never twist or pry the blade against the shell; back it out and recut instead. When every region is open, wipe the cut edges dry and drop in a battery LED puck.
Tools you'll need
For a intermediate carve like this you'll want a x-acto knife, poker tool, ribbon scoop, and painter's tape. Here's the kit we reach for — start with whatever you already own.
Elmchee Pumpkin Carving Kit
13-piece kit with carrying case
Saws for the larger cutouts, plus a scoop for hollowing. Covers both jobs in one kit.
View on Amazon ↗
HOME MOST LED Pumpkin Lights
4-pack, battery operated, with remote + timer
Orange glow made for jack-o'-lanterns. The remote and timer light the pumpkin every evening without reaching inside.
View on Amazon ↗
Speedball 4131 Lino Cutter Set
Handle + 5 interchangeable cutters
Interchangeable cutters for peeling and shading the face. Useful for the finer details.
View on Amazon ↗
Community Pumpkin Carving Ideas
Carving ideas that use stencils like this one.
Related stencils
Carvers who liked this one also downloaded these.
Expert / ProWide-Eyed Owl on a Branch
A magnificent wide-eyed owl perched on a curving branch, rendered in layered relief: feathered brow tufts, a sharp beak, ringed eyes, overlapping wing feathers, and a scalloped breast. Nothing is pierced; the entire portrait is carved by shaving the skin to varying depths so backlight grades from bright to dim across the feathers. This is expert work, so sharpen your loop tools, carve the deepest layers around the eyes first, and build the feather texture in shallow passes.
IntermediateDeer Head with Eight Tines
A buck's head glows from the pumpkin with a full eight-tine rack of antlers, alert ears, and a rounded muzzle, all carved as connected pierced openings. The antler beams branch symmetrically above the head, throwing dramatic spiky light. The narrow antler tines are the challenge here; saw each tine from its tip down toward the main beam and avoid twisting the blade so the slender channels stay clean.
AdvancedSitting Rabbit with Long Ears
A serene rabbit sits in profile with tall upright ears, delicate whiskers, and a rounded haunch, filling most of the pumpkin's face. The entire figure is shaved from the skin as a raised relief, with fine scored lines suggesting fur and limb contours, so nothing pierces the wall and it works beautifully as a table centerpiece. Shave the broad body areas first, then add the fur strokes with light flicks of a detail knife.
AdvancedDragonfly with Reeds
A dragonfly hovers with all four veined wings spread wide, its long segmented tail trailing down among slender reed grasses and cattails. The whole scene is shave-carved: wings, body, and reeds glow through thinned skin while the background stays dark, with no pierced holes. The wing veining is the payoff detail, so shave each wing smooth first, then score the vein lines lightly with a knife tip rather than gouging them.
IntermediateBee with Three Raw Stripes
A friendly bumblebee spreads four scalloped wings wide, with a round head, curled antennae, and a plump body banded by three raw stripes. This is a shading design with no pierced holes: the wings, head, and body stripes are shaved down to pale flesh while strips of dark skin form the outlines and bands. Shave the big wing panels first, then refine the narrow antennae with a small gouge.
AdvancedStanding Duck with Webbed Feet
A standing duck in profile, from its rounded bill down to its webbed feet, with layered feather detail across the folded wing and breast. This is a skin-shaving pattern rather than a pierced one: the duck's body is etched to glow while the surrounding skin stays dark, and feather lines are scored deeper for texture. Shave the broad body areas first, then add the fine feather strokes last so a slip cannot erase your detail work.