Similar to This
View all stencils →About this stencil
A long-necked brachiosaurus stretches up toward three tropical leaves floating above it, its full body cut through as one flowing silhouette from tail tip to tiny head. The leaves are separate cutouts with notched edges that add extra glow around the dino's snack. Cut the leaves first for practice, then work the dinosaur from the tail forward, saving the slender neck for careful final strokes. This design is rated Intermediate and takes most carvers around 75 minutes from trace to glow. Comfortable knife handling required. Small details and curves.
Pumpkin size guide
- 🎃 Small (5–7") — print at 80%
- 🎃 Medium (7–10") — print at 100% (recommended)
- 🎃 Large (11–13") — print at 130%
- 🎃 Giant (14"+) — print at 150% on tabloid paper
Frequently asked questions
Can I resize this stencil?▾
Yes. The PDF is vector so it scales cleanly. Print at 100% for a 7–10 inch pumpkin, 130% for 11–13 inch, or 150% for a giant. Use your printer's "Fit to page" or "Custom scale" setting.
What kind of paper works best?▾
Standard 20 lb letter or A4 printer paper is fine. Heavier paper is harder to bend around the pumpkin curve. If your printer supports it, set the quality to 'best' so the lines are crisp.
How long will the carved pumpkin last?▾
Usually 5–10 days. Coat all cut surfaces with petroleum jelly and store the pumpkin somewhere cool overnight. Avoid direct sun. Battery LED pumpkin lights produce no heat and double the lifespan.
Can I sell pumpkins carved with this stencil?▾
Yes, the carved pumpkin you make is yours. The license covers personal and small-scale commercial carving (selling carved pumpkins, photographing them, posting on social). You may not resell the PDF file itself.
What if my printer doesn't print the whole stencil?▾
Set 'Page scaling' to 'Fit' in the print dialog and uncheck 'Auto-rotate'. If it still cuts off, the design includes 0.25" of safe-area margin so a small crop won't ruin it.
How to carve this stencil
- 1Print it
Download the PDF and print at 100% scale on letter or A4 paper.
- 2Prep the pumpkin
Cut the lid at an angle, scoop the guts, thin the wall to ~1 inch.
- 3Tape it on
Snip darts in the paper so it lies flat against the curve.
- 4Transfer the design
Poke along every line — about one dot every 1/8 inch.
- 5Carve it
Connect the dots with short straight cuts. Center first, work outward.
- 6Light it up
Drop in a battery LED pumpkin light and you're done.
Tools you'll need
For a intermediate carve like this you'll want a x-acto knife, poker tool, ribbon scoop, and painter's tape. Here's the kit we reach for — start with whatever you already own.
Elmchee Pumpkin Carving Kit
13-piece kit with carrying case
Saws for the larger cutouts, plus a scoop for hollowing. Covers both jobs in one kit.
View on Amazon ↗
HOME MOST LED Pumpkin Lights
4-pack, battery operated, with remote + timer
Orange glow made for jack-o'-lanterns. The remote and timer light the pumpkin every evening without reaching inside.
View on Amazon ↗
Speedball 4131 Lino Cutter Set
Handle + 5 interchangeable cutters
Interchangeable cutters for peeling and shading the face. Useful for the finer details.
View on Amazon ↗
Community Pumpkin Carving Ideas
Carving ideas that use stencils like this one.
Related stencils
Carvers who liked this one also downloaded these.
AdvancedTriceratops Pumpkin Stencil
A chubby cartoon triceratops in a walking pose fills this hard pumpkin stencil: a large frilled head with three prominent horns, two small oval nostril dots and a crescent eye below the frill, a round body, four chunky legs with pointed toe claws, and a short upturned tail. The frill at the back of the head is an open silhouette that glows as a scalloped arc. Cut the three horn outlines and the two small nostril dots first before the broader body and leg cutouts, as the nostril dots are isolated and easiest to control while the pumpkin is still intact.
AdvancedStegosaurus Pumpkin Stencil
A cartoon stegosaurus with a round friendly face, four chunky legs, and a row of large diamond-shaped back plates fills this hard pumpkin stencil. The body is carved as a wide open pierce, the back plates are pierced individually above it, and the toes and facial details are fine cut-outs. When lit, the dinosaur glows as a bright segmented shape with the plates hovering above the silhouette. Carve the face details and tiny toe lines before removing the large body section, since the body cut-through will flex the pumpkin wall and make those small details harder to control.
AdvancedParasaurolophus Pumpkin Stencil
A cute bipedal Parasaurolophus dinosaur faces right in this hard-level pumpkin stencil, with the signature backward-sweeping cranial crest arching above its round eye, a chunky body sectioned by organic blob-shaped cut-outs along the dorsal ridge and belly, two short front arms with clawed fingers, and sturdy hind legs. The blob-shaped body cut-outs stay open so the dinosaur glows in a spotted pattern when lit, while the outer silhouette stays solid. Cut the small claw details on the fingers before removing the large body sections so the arm area keeps its rigidity while you work.
IntermediateSmiling Sea Turtle
A smiling sea turtle paddles across the pumpkin, its patterned shell divided into glowing plates while thin ribbons of skin stay in place to draw the head, flippers, and shell segments. This is a shading-style design carved on a continuous wall, so you shave away the skin rather than piercing holes, letting the whole turtle glow softly. Shave in thin layers and test with a light often until the flippers and shell panels shine evenly.
IntermediateLeaping Dolphin & Two Waves
A dolphin arcs joyfully above two rolling waves, its curved body, dorsal fin, flippers, and smiling beak all drawn in bright shaded lines. The design uses skin-shave shading only, so you scrape away the outer skin along the dolphin and wave shapes while the wall stays solid. At medium difficulty, work the long body curve in one smooth continuous pass before adding the wave lines, which keeps the leap looking fluid.
AdvancedStanding Duck with Webbed Feet
A standing duck in profile, from its rounded bill down to its webbed feet, with layered feather detail across the folded wing and breast. This is a skin-shaving pattern rather than a pierced one: the duck's body is etched to glow while the surrounding skin stays dark, and feather lines are scored deeper for texture. Shave the broad body areas first, then add the fine feather strokes last so a slip cannot erase your detail work.