The 2026 contest winners are inGrand Prize, People's Choice and Most Creative, all crowned.
@ai_concepts
Sep 25, 2026
Two Sweethearts Kitten PumpkinAI
0

Report this carving

Tell us what is wrong. Reports are private.

Two Sweethearts Kitten Pumpkin

Two side-by-side kitten faces, each with separate eyes, smiles, whiskers and heart holes, plus small round accent cutouts between them, fill this hard cute cat pumpkin carving with playful energy. All openings are independent with wide rind preserved between every cut, so the dense layout stays structurally sound. Sketch both faces before cutting and confirm the rind between the two face areas is at least two centimeters wide. A bright LED inside makes all the small accents read clearly from across the room.

No ratings yet · Sign in to rate
HardAnimalsCuteClassic Cutout
cute-catanimalcutecattwo-facesheartround-accentkitten

Save this design for carving night, then share a photo of your own jack-o'-lantern once it's glowing.

Comments (0)

  • No comments yet. Be the first.

Our tips for carving a similar design

Fitting two complete kitten faces on one pumpkin demands careful pre-planning of the rind corridor between them. Every opening, eyes, smiles, whiskers, hearts and round accents, must be independent with wide rind preserved between each cut. Sketching both faces first and measuring the gap between them before cutting is non-negotiable at this complexity level.

From pumpkin to porch

  1. Choose a large pumpkin

    This design requires a wide, relatively flat-faced pumpkin at least 30 cm across. A tall narrow pumpkin will not have enough horizontal surface for two full faces. Check the width before purchasing and choose the flattest face side as your carving surface.

  2. Sketch both faces before cutting

    Use a pencil to sketch both kitten faces in full on the pumpkin surface, including every opening. Measure the rind corridor between the two face areas and confirm it is at least 2 cm wide at its narrowest point. Adjust the face sizes down if the gap is tighter than that.

  3. Transfer the pattern precisely

    Poke through the full pattern with a pin and connect the dots with a fine marker. Mark all heart holes, round accents and whisker positions for both faces at this stage. Having the complete roadmap visible before any blade touches the pumpkin prevents improvised cuts that compromise the structure.

  4. Carve one face completely before starting the second

    Carve all openings of the first kitten face from top to bottom, checking rind stability after each cut. Completing one face gives you a clear sense of how the pumpkin's rind is behaving before you commit to the second. If the wall feels thin or fragile after the first face, reinforce with tape before continuing.

  5. Carve the second face

    Carve the second kitten face using the same order as the first: eyes, then smile, then whiskers, then heart, then accent holes. Work slowly near the rind corridor between the two faces; this strip carries structural load for both sides and must stay at least 2 cm wide.

  6. Light with a bright LED

    A single bright LED in the center of the interior will illuminate both faces evenly. Check from a viewing distance that all small accents read clearly. Apply petroleum jelly to every cut edge and display the pumpkin on a table where both faces are easily seen.

Written with AI to match this design

Gather your supplies

Check things off as you get ready.

Work on a stable surface, keep your free hand out of the cutting path, and have an adult handle sharp tools.

Three levels of light

  • Leave intact

    The rind corridor between the two faces, all bridge rind between each face's features and the outer edge stays solid.

  • Peel & shade

    None. All glow is from cut-throughs.

  • Cut through

    All eyes, smiles, whisker holes, heart holes and round accent holes on both kitten faces are cut through for full light.

Learn the carving basics

Before you start cutting

What if the pumpkin surface curves too much for two flat faces?

On a curved surface, reduce each face to its most essential elements: two eyes and a smile per kitten, skipping the accent holes. Simpler shapes follow the curve more easily and still read as two distinct kitten faces when lit. You can add painted-on whiskers after carving if you want more detail.

How do I keep the two faces looking symmetrical with each other?

Trace both faces from the same pattern at the same scale, placing your template at the same height on each side of the pumpkin. Measure from the top center of the pumpkin down to the eye level of each face to confirm they match before cutting. Small asymmetries are charming, but large height differences look like a mistake.

Can I use one candle for both faces?

A real candle is not recommended here due to the fire risk near children and pets. A single bright LED puck placed center-interior will cast light toward both faces. If one face seems dim, add a second LED to the side of the interior nearest the dimmer face.

Your take belongs here, too.

Changed a detail? Made it simpler? Share a photo of your version and tell the community what worked.

Share your pumpkin

Want more designs like this? Browse our full library of pumpkin carving ideas, or pick a free printable stencil. Every pattern and template in our own collection is free to print at home.

More pumpkins like this

You've reached the end · 8 pumpkins
The Patch Report

Fresh pumpkins, in your inbox.

The best new carvings, ideas worth stealing, and how-tos for carving season. Short, seasonal, and gone by November.

A short email during carving season. Unsubscribe anytime. See our privacy policy.