Similar to This
View all stencils →About this stencil
A soaring pterodactyl caught mid-flight, with one wing swept high and the other stretched wide, a long crested head, open beak, and trailing legs. The whole silhouette is shaded by shaving away the skin, so the pale flying reptile appears against the darker pumpkin without any pierced holes. At medium difficulty the key is the wing edges: score the outline first with a light pass, then scrape inward so the membrane shapes stay crisp. This design is rated Intermediate and takes most carvers around 75 minutes from trace to glow. Comfortable knife handling required. Small details and curves.
Pumpkin size guide
- 🎃 Small (5–7") — print at 80%
- 🎃 Medium (7–10") — print at 100% (recommended)
- 🎃 Large (11–13") — print at 130%
- 🎃 Giant (14"+) — print at 150% on tabloid paper
Frequently asked questions
Can I resize this stencil?▾
Yes. The PDF is vector so it scales cleanly. Print at 100% for a 7–10 inch pumpkin, 130% for 11–13 inch, or 150% for a giant. Use your printer's "Fit to page" or "Custom scale" setting.
What kind of paper works best?▾
Standard 20 lb letter or A4 printer paper is fine. Heavier paper is harder to bend around the pumpkin curve. If your printer supports it, set the quality to 'best' so the lines are crisp.
How long will the carved pumpkin last?▾
Usually 5–10 days. Coat all cut surfaces with petroleum jelly and store the pumpkin somewhere cool overnight. Avoid direct sun. Battery LED pumpkin lights produce no heat and double the lifespan.
Can I sell pumpkins carved with this stencil?▾
Yes, the carved pumpkin you make is yours. The license covers personal and small-scale commercial carving (selling carved pumpkins, photographing them, posting on social). You may not resell the PDF file itself.
What if my printer doesn't print the whole stencil?▾
Set 'Page scaling' to 'Fit' in the print dialog and uncheck 'Auto-rotate'. If it still cuts off, the design includes 0.25" of safe-area margin so a small crop won't ruin it.
How to carve this stencil
- 1Print it
Download the PDF and print at 100% scale on letter or A4 paper.
- 2Prep the pumpkin
Cut the lid at an angle, scoop the guts, thin the wall to ~1 inch.
- 3Tape it on
Snip darts in the paper so it lies flat against the curve.
- 4Transfer the design
Poke along every line — about one dot every 1/8 inch.
- 5Carve it
Connect the dots with short straight cuts. Center first, work outward.
- 6Light it up
Drop in a battery LED pumpkin light and you're done.
Tools you'll need
For a intermediate carve like this you'll want a x-acto knife, poker tool, ribbon scoop, and painter's tape. Here's the kit we reach for — start with whatever you already own.
Elmchee Pumpkin Carving Kit
13-piece kit with carrying case
Saws for the larger cutouts, plus a scoop for hollowing. Covers both jobs in one kit.
View on Amazon ↗
HOME MOST LED Pumpkin Lights
4-pack, battery operated, with remote + timer
Orange glow made for jack-o'-lanterns. The remote and timer light the pumpkin every evening without reaching inside.
View on Amazon ↗
Speedball 4131 Lino Cutter Set
Handle + 5 interchangeable cutters
Interchangeable cutters for peeling and shading the face. Useful for the finer details.
View on Amazon ↗
Community Pumpkin Carving Ideas
Carving ideas that use stencils like this one.
Related stencils
Carvers who liked this one also downloaded these.
Expert / ProDomed Jellyfish and Bubbles
A ribbed jellyfish bell hovers near the top of the pumpkin, trailing eight long wavy tentacles that flow all the way to the base, with small bubbles rising on either side. The bell segments and tentacles are shaved to glowing flesh while thin strips of dark skin separate every ribbon, and the bubbles are pierced through. This expert shading design demands a steady hand; work each tentacle top to bottom in one continuous peel so the curves stay smooth and evenly lit.
IntermediateRunning Dinosaur and Long Tail
A velociraptor sprints across the pumpkin in full silhouette, head low, clawed legs mid-stride, and its long tail sweeping behind for balance. The entire dinosaur cuts through as one glowing shape, with the narrow tail and slim legs providing the medium challenge. Carve the thin tail and leg sections first in short segments, then remove the large body last so the delicate extremities are never left unsupported.
Expert / ProJellyfish with Fifteen Bubbles
A dramatic jellyfish drifts down the tall face of the pumpkin, its ribbed bell crowning a tangle of long ribbon tentacles surrounded by fifteen bubbles of varying size. Everything is shaved relief with no pierced holes, and the overlapping tentacles at different depths are what make it an expert etch. Vary your shaving depth deliberately, deepest where tentacles cross behind others, to build the layered, flowing effect.
AdvancedSpotted Whale Shark
A whale shark glides across the pumpkin, its wide flat head, tall tail fin, and body covered in the species' signature grid of pale spots, with a few bubbles drifting nearby. The shark's outline and spots are shaved to glow while the surrounding skin stays dark, so no section is pierced through. Do the long body outline first, then the spots; a small round scoop or melon-baller keeps all those dots consistent.
AdvancedDolphin above Curling Waves
A dolphin arcs above curling surf, its body, fins, and the rolling wave scrolls all shaved into the pumpkin skin with no pierced holes. Deeper shaving on the belly and wave crests makes those areas glow brightest, while shallow passes keep the outlines crisp. Vary your depth deliberately: the contrast between bright and dim is what gives this relief scene its sense of motion.
AdvancedHammerhead with Raw Back
A sculptural hammerhead shark carved in raised relief, with the background cleared away so the body, fins, and curved tail stand proud of the wall in layered depths. Fin edges, the mouth line, and gill grooves are incised for realistic detail while nothing pierces through. Rough out the background to one even depth before shaping the shark itself, and keep at least half the wall thickness so the raised body stays sturdy.