Similar to This
View all stencils →About this stencil
Three toadstool mushrooms of staggered heights cluster at the base of a tall pumpkin, with four round dots floating above them like drifting spores. The mushroom caps, stems, and dots are all cut fully through, so the whole woodland scene glows as connected pools of light. For this medium carve, cut the two small side mushrooms first to warm up, then tackle the big center cap; leave the narrow stem-to-cap junctions until your final passes. This design is rated Intermediate and takes most carvers around 75 minutes from trace to glow. Comfortable knife handling required. Small details and curves.
Pumpkin size guide
- 🎃 Small (5–7") — print at 80%
- 🎃 Medium (7–10") — print at 100% (recommended)
- 🎃 Large (11–13") — print at 130%
- 🎃 Giant (14"+) — print at 150% on tabloid paper
Frequently asked questions
Can I resize this stencil?▾
Yes. The PDF is vector so it scales cleanly. Print at 100% for a 7–10 inch pumpkin, 130% for 11–13 inch, or 150% for a giant. Use your printer's "Fit to page" or "Custom scale" setting.
What kind of paper works best?▾
Standard 20 lb letter or A4 printer paper is fine. Heavier paper is harder to bend around the pumpkin curve. If your printer supports it, set the quality to 'best' so the lines are crisp.
How long will the carved pumpkin last?▾
Usually 5–10 days. Coat all cut surfaces with petroleum jelly and store the pumpkin somewhere cool overnight. Avoid direct sun. Battery LED pumpkin lights produce no heat and double the lifespan.
Can I sell pumpkins carved with this stencil?▾
Yes, the carved pumpkin you make is yours. The license covers personal and small-scale commercial carving (selling carved pumpkins, photographing them, posting on social). You may not resell the PDF file itself.
What if my printer doesn't print the whole stencil?▾
Set 'Page scaling' to 'Fit' in the print dialog and uncheck 'Auto-rotate'. If it still cuts off, the design includes 0.25" of safe-area margin so a small crop won't ruin it.
How to carve this stencil
- 1Print it
Download the PDF and print at 100% scale on letter or A4 paper.
- 2Prep the pumpkin
Cut the lid at an angle, scoop the guts, thin the wall to ~1 inch.
- 3Tape it on
Snip darts in the paper so it lies flat against the curve.
- 4Transfer the design
Poke along every line — about one dot every 1/8 inch.
- 5Carve it
Connect the dots with short straight cuts. Center first, work outward.
- 6Light it up
Drop in a battery LED pumpkin light and you're done.
Tools you'll need
For a intermediate carve like this you'll want a x-acto knife, poker tool, ribbon scoop, and painter's tape. Here's the kit we reach for — start with whatever you already own.
Elmchee Pumpkin Carving Kit
13-piece kit with carrying case
Saws for the larger cutouts, plus a scoop for hollowing. Covers both jobs in one kit.
View on Amazon ↗
HOME MOST LED Pumpkin Lights
4-pack, battery operated, with remote + timer
Orange glow made for jack-o'-lanterns. The remote and timer light the pumpkin every evening without reaching inside.
View on Amazon ↗
Speedball 4131 Lino Cutter Set
Handle + 5 interchangeable cutters
Interchangeable cutters for peeling and shading the face. Useful for the finer details.
View on Amazon ↗
Community Pumpkin Carving Ideas
Carving ideas that use stencils like this one.
Related stencils
Carvers who liked this one also downloaded these.
Expert / ProWoodland Toadstool Relief
An enchanted cluster of spotted toadstools carved in deep relief: one grand mushroom with a striped, gilled underside towers over smaller caps, ribbed stems, and leafy ground cover below. There are no pierced holes; the whole scene is sculpted by shaving the wall to different depths so light glows warmest under the big cap. This expert design rewards planning, so rough out the major cap shapes first and save the fine gill lines and spots for last.
Expert / ProFour Woodland Toadstools
Four spotted woodland toadstools cluster among curling leaves and grasses, carved in deep relief so the caps, gills, and stems stand out from the shell in true sculptural layers. Nothing is pierced; the design is built entirely by shaving and sculpting the wall to different depths, with the tall center mushroom's gilled underside as the showpiece. Rough out the deepest background first, then refine the gill lines last with a V-gouge while the ridges are still thick.
Expert / ProFour Spotted Toadstools
Four spotted toadstools of staggered heights grow from a glowing patch of grass, the tallest cap arching over three smaller companions. This expert shading piece uses multiple depths: gills under the big cap are shaved brightest, stems and caps sit mid-tone, and the spots are left as darker raised dots. Map your depth levels before touching a tool, and carve the delicate gill lines with a fine gouge in single confident strokes.
IntermediateBee with Three Raw Stripes
A friendly bumblebee spreads four scalloped wings wide, with a round head, curled antennae, and a plump body banded by three raw stripes. This is a shading design with no pierced holes: the wings, head, and body stripes are shaved down to pale flesh while strips of dark skin form the outlines and bands. Shave the big wing panels first, then refine the narrow antennae with a small gouge.
IntermediateEight Petals with Leaf Pair
Eight almond-shaped petals radiate around a solid center in this graceful flower design, with a pair of pointed leaves below and small accent holes dotting each side like falling seeds. All the petals, leaves, and dots are pierced through while the round flower center stays intact, held by the uncut spokes between petals. For this medium carve, cut opposite petals in pairs as you work around the circle so pressure stays balanced and the center never loosens.
Beginner-friendlyBroad Cap Mushroom
A single broad-capped mushroom with a sturdy stem glows from the center of the pumpkin in this cozy woodland design. The whole mushroom is removed as one connected cutout, cap and stem together, so there are no fragile bridges to protect. That makes it a great easy project for porch-step decorating; cut the smooth dome of the cap in one continuous pass, then square off the stem base last for a clean silhouette.