Similar to This
View all stencils →About this stencil
A serene jellyfish drifts across the pumpkin, its smooth dome bell trailing five wavy tentacles among scattered bubbles. Nothing is pierced; the entire design is shaved into the skin so the bell, tentacles, and bubbles appear as pale carved relief against the orange rind. For this medium etch, remove only the skin and a thin layer of flesh at an even depth so the lines stay crisp and uniform. This design is rated Intermediate and takes most carvers around 75 minutes from trace to glow. Comfortable knife handling required. Small details and curves.
Pumpkin size guide
- 🎃 Small (5–7") — print at 80%
- 🎃 Medium (7–10") — print at 100% (recommended)
- 🎃 Large (11–13") — print at 130%
- 🎃 Giant (14"+) — print at 150% on tabloid paper
Frequently asked questions
Can I resize this stencil?▾
Yes. The PDF is vector so it scales cleanly. Print at 100% for a 7–10 inch pumpkin, 130% for 11–13 inch, or 150% for a giant. Use your printer's "Fit to page" or "Custom scale" setting.
What kind of paper works best?▾
Standard 20 lb letter or A4 printer paper is fine. Heavier paper is harder to bend around the pumpkin curve. If your printer supports it, set the quality to 'best' so the lines are crisp.
How long will the carved pumpkin last?▾
Usually 5–10 days. Coat all cut surfaces with petroleum jelly and store the pumpkin somewhere cool overnight. Avoid direct sun. Battery LED pumpkin lights produce no heat and double the lifespan.
Can I sell pumpkins carved with this stencil?▾
Yes, the carved pumpkin you make is yours. The license covers personal and small-scale commercial carving (selling carved pumpkins, photographing them, posting on social). You may not resell the PDF file itself.
What if my printer doesn't print the whole stencil?▾
Set 'Page scaling' to 'Fit' in the print dialog and uncheck 'Auto-rotate'. If it still cuts off, the design includes 0.25" of safe-area margin so a small crop won't ruin it.
How to carve this stencil
- 1Print it
Download the PDF and print at 100% scale on letter or A4 paper.
- 2Prep the pumpkin
Cut the lid at an angle, scoop the guts, thin the wall to ~1 inch.
- 3Tape it on
Snip darts in the paper so it lies flat against the curve.
- 4Transfer the design
Poke along every line — about one dot every 1/8 inch.
- 5Carve it
Connect the dots with short straight cuts. Center first, work outward.
- 6Light it up
Drop in a battery LED pumpkin light and you're done.
Tools you'll need
For a intermediate carve like this you'll want a x-acto knife, poker tool, ribbon scoop, and painter's tape. Here's the kit we reach for — start with whatever you already own.
Elmchee Pumpkin Carving Kit
13-piece kit with carrying case
Saws for the larger cutouts, plus a scoop for hollowing. Covers both jobs in one kit.
View on Amazon ↗
HOME MOST LED Pumpkin Lights
4-pack, battery operated, with remote + timer
Orange glow made for jack-o'-lanterns. The remote and timer light the pumpkin every evening without reaching inside.
View on Amazon ↗
Speedball 4131 Lino Cutter Set
Handle + 5 interchangeable cutters
Interchangeable cutters for peeling and shading the face. Useful for the finer details.
View on Amazon ↗
Community Pumpkin Carving Ideas
Carving ideas that use stencils like this one.
Related stencils
Carvers who liked this one also downloaded these.
Expert / ProMoonlit Seal and Water Bands
A harbor seal rests on the shore with its head raised and tail curled up, backed by a huge full moon, drifting clouds, and bands of rippling water below. The entire scene is skin-shaved shading with no pierced holes, so the moon glows brightest behind the seal's darker sculpted body. Expert carvers should establish the moon's deep, even shave first, then build the seal with shallower graded layers so its whiskered face keeps crisp contrast.
IntermediateFan Tail Fish with Low Notches
A plump fantail goldfish glides across the pumpkin as one big glowing silhouette, with a rounded body, sweeping double tail, and small notched fins along the belly. The entire fish is pierced through in a single connected shape, so it lights up like an aquarium at night. At medium difficulty the low fin notches are the detail work; cut the broad body and tail first, then nick out the small fin points with short careful strokes.
IntermediateSeated Rabbit with Split Ears
A seated rabbit in profile with two tall split ears, a rounded back, and tucked front paws, cut through as a nearly single silhouette with slim gaps defining the ears and feet. The shell around the bunny stays whole so the glowing shape reads crisply from a distance. Carve the narrow gap between the ears first; it is the finest cut on an otherwise smooth outline.
Beginner-friendlySeated Dog with Bone and Dots
A patient pup sits in profile, ears perked and tail resting, while a bone floats nearby with a trail of small dream-bubble dots connecting them. The dog's body, the bone, and the dots are all cut fully through as bold, separate openings, so the scene reads instantly from the street. This easy design has no fragile interior bridges; just cut the large dog body in two or three sections and pop the bone and dots out last for a tidy finish.
Beginner-friendlyTall Toes Above a Low Paw Pad
A big glowing paw print built from four oval toe pads arranged above one broad heart-shaped main pad. All five shapes cut cleanly through the wall, and the generous spacing between pads makes the layout very forgiving. Drill a starter hole in the center of each pad and saw outward to the line; the smooth convex curves are ideal practice strokes for young or first-time carvers.
Beginner-friendlyPlus Above Four Windows
A bold medical plus sign glows at the top while a row of small square windows and a larger doorway below turn the pumpkin into a tiny lit-up hospital. Every shape cuts straight through, and the straight-edged squares make this an easy, tidy carve, perfect for healthcare workers or a first-responder porch display. Score each square with a ruler before cutting so the windows line up in a neat row.