Halloween Pumpkin Carving Contest · Starts October 1st · $500 in prizes
See the contest →
+ Upload
← Back to ideas
@ai_concepts
Sep 25, 2026
Diagonal-Eyed Skinny Pumpkin on a Narrow Porch LedgeAI
0

Report this carving

Tell us what is wrong. Reports are private.

Diagonal-Eyed Skinny Pumpkin on a Narrow Porch Ledge

Two short diagonal triangular eyes and a narrow vertical oval mouth give this 35-centimeter skinny pumpkin a quirky off-kilter expression that plays up its unusual proportions. Angle the eye triangles so they tilt inward toward the center, which reads as narrowed eyes and adds personality without extra cuts. The narrow oval mouth fits naturally in the limited width, so trace it to fill the available space without touching the side rind. This skinny pumpkin carving idea looks best at close range on a ledge or windowsill where its narrow silhouette is framed against the wall behind.

No ratings yet · Sign in to rate
EasyFacesClassicClassic Cutout
skinnyfaceclassiceasydiagonal-eyenarrow-oval-mouthporch-ledgequirky-expression

Comments (0)

  • No comments yet — be the first.

Save without an account. Sign in to like or comment.

Our tips for carving a similar design

The design leans on the pumpkin's narrow proportions to make two inward-tilting diagonal triangles read as narrowed, knowing eyes. A single narrow oval mouth fills the limited width without crowding the edges. Three clean cutouts are all you need.

From pumpkin to porch

  1. Prep the pumpkin

    Wipe the surface clean and dry. Cut the lid at an angle so it locks back in place and does not fall inside. Scoop the interior down to about 2.5 centimeters of wall thickness so light spreads evenly and cutting is not fighting thick flesh.

  2. Mark the eye triangles

    Center your two triangles on the upper face. Tilt each one so the inner corner angles downward toward the pumpkin's center line, giving the inward-narrowed look. Keep each triangle under 4 centimeters across so it fits the 17-centimeter width comfortably with rind on all sides.

  3. Mark the oval mouth

    Draw a narrow vertical oval below the eyes. It should span only about 4 to 5 centimeters wide to stay within the slim face area. Make it taller than wide to reinforce the skinny proportions.

  4. Cut the eyes

    Use a thin serrated pumpkin saw to follow the diagonal lines. Cut the eyes before the mouth so any flex in the pumpkin wall does not shift already open areas. Push each triangle plug inward to remove it cleanly.

  5. Cut the mouth

    Follow the oval outline with slow, deliberate saw strokes, keeping the blade perpendicular to the rind surface. An oval is a continuous curve, so work in one fluid motion rather than stopping and restarting. Push the oval plug inward.

  6. Light and display

    Drop an LED tea light inside rather than a candle. Place the pumpkin on a narrow ledge or windowsill where its slim silhouette is visible in profile as well as face-on. A wall behind it will catch the projected light nicely.

Written with AI to match this design

Gather your supplies

Check things off as you get ready.

Work on a stable surface, keep your free hand out of the cutting path, and have an adult handle sharp tools.

Three levels of light

  • Leave intact

    All surrounding rind and the broad vertical bands on either side of the face remain solid and dark.

  • Peel & shade

    None. This design uses only full cutouts.

  • Cut through

    Both diagonal triangular eyes and the narrow vertical oval mouth are cut all the way through for full warm light.

Learn the carving basics

Before you start cutting

Will the narrow pumpkin crack when I cut it?

Skinny pumpkins have less wall area to distribute stress, so keep cuts small and work slowly. Scoop the inside to an even thickness first. If you hear crackling, stop and re-score the line before continuing.

How do I get the diagonal tilt on the eyes consistent?

Draw a faint center line down the face vertically, then angle each triangle so its inner lower corner sits on or near that line. Eyeballing symmetry is easier when you have that reference line to work from.

Can I use this design on a round pumpkin instead?

You can, but the diagonal-eye trick works best when the face is narrow. On a round pumpkin the same angles will still look expressive but the off-kilter personality is less pronounced without the skinny silhouette to reinforce it.

Your take belongs here, too.

Changed a detail? Made it simpler? Share a photo of your version and tell the community what worked.

Share your pumpkin

More pumpkins like this

Stacked Ghost Skinny Pumpkin on a Kitchen Counter
AI
Stacked Ghost Skinny Pumpkin on a Kitchen Counter
@ai_concepts0
Trailing Vine Painted Tall Skinny Pumpkin on a Porch
AI
Trailing Vine Painted Tall Skinny Pumpkin on a Porch
@ai_concepts0
Ghost-Surprised Face Very Tall Skinny Pumpkin
AI
Ghost-Surprised Face Very Tall Skinny Pumpkin
@ai_concepts0
Classic Jack-O-Lantern Plastic Pumpkin With Single Tooth
AI
Classic Jack-O-Lantern Plastic Pumpkin With Single Tooth
@ai_concepts0
Daisy Cluster Painted No-Carve Plastic Pumpkin
AI
Daisy Cluster Painted No-Carve Plastic Pumpkin
@ai_concepts0
Moon and Star Painted No-Carve Turnip Lantern
AI
Moon and Star Painted No-Carve Turnip Lantern
@ai_concepts0
Traditional Turnip Jack-O-Lantern With Triangle Eyes
AI
Traditional Turnip Jack-O-Lantern With Triangle Eyes
@ai_concepts0
Daisy Band Painted Flat Pumpkin on a Patio Table
AI
Daisy Band Painted Flat Pumpkin on a Patio Table
@ai_concepts0
You've reached the end · 8 pumpkins
The Patch Report

Fresh pumpkins, in your inbox.

The best new carvings, ideas worth stealing, and how-tos for carving season. Short, seasonal, and gone by November.

A short email during carving season. Unsubscribe anytime. See our privacy policy.